Something is probably wrong with your network if this is the case. Have you tried replacing the network cables and ensuring the switch port is ok?
BTW, this server is set up to use multiple connections, with at least one as a backup. You can use
to check which adapters are set as primary/secondary adapters.
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
I suspect that someone is using a sniffer on my Ethernet connection,
OS X 10.3.9, DSL,
ok, I'm in terminal using the "ifconfig" command >
flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384
right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
LEARN ABOUT DEBIAN
rsuplnk
RSUPLNK(8) Linux Programmer's Manual RSUPLNK(8)NAME
rsuplnk - User entry into the ROSE network.
SYNOPSIS
rsuplnk [-q] <port>
DESCRIPTION
The rsuplnk program allows a user to gain entry into the ROSE network using the standard pseudo-digipeating method. Recent Linux kernels
are aware of this form of operation and the ax25d program can listen for such connections. The normal mode of operation of a ROSE switch is
to have one ROSE address (ie port) per physical AX.25 port. Therefore ROSE users coming in on a given AX.25 port will appear as if they
come from the associated ROSE port. This is the reason for the need for a ROSE port as an argument.
To use rsuplnk you need an entry in ax25d.conf to listen for incoming connections. In the example below, I will be listening for ROSE con-
nections on my AX.25 port 144 using the callsign KE4GAJ-10 and the ROSE port associated with the AX.25 port is rs144.
#
[KE4GAJ-10* VIA 144]
NOCALL * * * * * * L
default * * * * * * - root /usr/sbin/rsuplnk rsuplnk rs144
#
There would typically be one rsuplnk per user access AX.25 port. The associated program for exiting a ROSE network is rsdwnlnk.
All errors generated by rsuplnk are written to the system debug log file.
OPTIONS -q Supresses the messages generated by rsuplnk when making the connection.
FILES
/etc/ax25/rsports
SEE ALSO rose(4), ax25d.conf(5), ax25d(8), rsdwnlnk(8), rose_call(8).
AUTHOR
Jonathan Naylor G4KLX <g4klx@g4klx.demon.co.uk>
Linux 29 April 1997 RSUPLNK(8)