hi all
iam trying to set my eri0 interface but with little luck .
when i set the ip using ipconfig i always get "bad adress"..
moreover when i use ifconfig eri0 i can notice that the inet is 0.0.0.0 and the netmask 0
i am runnig solaris 9 on sparc .
any helpis highly appreciated ... ... (2 Replies)
Hello,
I have a server with two ip addresses. I need to make the ip address that's currently the secondary the primary. How do I use the ifconfig command and primary option?
Thanks. (5 Replies)
HI All,
My interface card has failed.If i am giving the command to uplumb it i am getting an error.
ce401001: flags=219040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,FAILED,CoS> mtu 1500 index 3
inet 10.188.24.18 netmask ffffffc0 broadcast 10.188.24.63
# ifconfig... (2 Replies)
hi,
i want to know how to grep inet address for below
below is the output of ifconfig command
/home/JA> ifconfig
eth0 Link encap:Ethernet HWaddr 00:11:0A:5B:2E:E9
inet addr:161.239.203.18 Bcast:161.239.203.127 Mask:255.255.255.128
UP BROADCAST RUNNING... (3 Replies)
Hello All,
Can someone show me how to cat "only the IP address of e1000g0" using ifconfig -a.
i am trying to grep only the ip address (xx.xx.xx.xx) from the bunch of all other things like, broadcast address, IPV4, UP........and so on.
thanks (1 Reply)
I'm working on an AIX Unix LPAR (AIX 3.5 00C3C9904C00 as returned by uname -a)
I can access this box using telnet, port 22 using adress IP A and B
A=AA.AA.XX.XX and B=AA.AA.YYY.YYY
I can confirm these 2 are the same space, I can see
I can't find address B listed anywhere... so I wonder what... (1 Reply)
I am running on AIX 5.3. I have a remote AIX server running on a generator. Many times the generator goes out and I only have a window of 15 mins with the network up and 30 mins the server is powered. I need help creating a script using ifconfig, where it goes out and checks the network every 5... (2 Replies)
hi,
I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address.
I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated.
before reboot:
eri0:... (3 Replies)
Hi
I am trying to create a script extracting the IP provided by ifconfig.
I tried with grep + awk but I am returned more than I need.
/sbin/ifconfig eth0 | grep "inet addr:" | awk '/inet addr:/ { print $2 }'
and returns
addr:10.15.1.64
How can I remove "addr:" string?... (9 Replies)
I am new to shell scripting and trying to create a shell script which will extract and print only ip address from ifconfig command and not all the information. I have two issues here -
1. To know active interface like eth0, wl0, etc.
- I guess `route` command will give me interface name in last... (3 Replies)
Discussion started by: amarshukla
3 Replies
LEARN ABOUT CENTOS
pppoe-setup
PPPOE-SETUP(8) System Manager's Manual PPPOE-SETUP(8)NAME
pppoe-setup - Shell script to configure Roaring Penguin PPPoE client
SYNOPSIS
pppoe-setup
DESCRIPTION
pppoe-setup is a shell script which prompts you for various pieces of information and sets up an /etc/sysconfig/network-scripts/ifcfg-ppp0
configuration script for the pppoe-start, pppoe-stop and +pppoe-connect scripts.
AUTHOR
pppoe-setup was written by David F. Skoll <dfs@roaringpenguin.com>.
The pppoe home page is http://www.roaringpenguin.com/pppoe/.
SEE ALSO pppoe(8), pppoe-start(8), pppoe-stop(8), pppoe-connect(8), pppd(8), pppoe.conf(5), pppoe-status(8), pppoe-sniff(8), pppoe-relay(8), pppoe-
server(8)4th Berkeley Distribution 21 February 2000 PPPOE-SETUP(8)