12-28-2008
I looks like you have messed up the primary/secondary drive configurations, and when you have both drives (old and new) both are set as primary, probably using the jumpers on the disks themselves.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I enquired before about adding another disk to an ultra 10...
and was told it was possible...
Well - since then I got my hands on another ultra 10 - and have taken the disk out of that one...
I should be able to connect it up - but I am wondering - should this be mounted in any partiulcar... (2 Replies)
Discussion started by: frustrated1
2 Replies
2. Solaris
Dear all ,
I am new to sun cluster and i having a problem adding a disk to a disk group .
My platfrom consists of a clustered E6900 SUN server and an EMC DX1000 storage .
the disk group that iam trying to add the disk to is shared group ,
whwen i run vxdisk list i get in status "online... (2 Replies)
Discussion started by: ppass
2 Replies
3. AIX
Hi,
I'm getting the errors below in the errpt report for a IBM Blade server. I'm guessing there's a problem with one of the disks but don't know how I can confirm this. Can anyone offer any suggestions?
Regards
Gareth (4 Replies)
Discussion started by: m223464
4 Replies
4. HP-UX
Hi dear(s)
Can u explain how to add a disk through lvm with commands.
I need to add a 9 gb scsi HS disk to a Hp D class 9000 server. (2 Replies)
Discussion started by: sreekumar.R
2 Replies
5. Filesystems, Disks and Memory
Wellcomes All,
some times ago I 've installed a Debian ditribution on an Hard Disk who was set as Primary Master. Few days ago, I 've decided to install another Hard Disk with a different Operating System. When I did that, I turned off the old hard disk, and I mouted the new one on the Primary IDE... (1 Reply)
Discussion started by: thekarsillo
1 Replies
6. Filesystems, Disks and Memory
Hello,
I wanted to share an experience I had today which was quite a learning experience and perhaps useful for others who may run into the issue at some point in the future.
Basically, the scenario involves a OS which was installed on a machine which hardware-wise, had a SATA Drive. The... (0 Replies)
Discussion started by: septima.pars
0 Replies
7. UNIX Desktop Questions & Answers
Hi there! I am installing Unixware 7.1 to a new server. We usually use SCSI hard for this but since this will be used only for testing, I decided to use an 80GB IDE hard disk. I was able to successfully load the unix but found out that the 80GB hard disk was not maximized. The total hard disk... (1 Reply)
Discussion started by: limpinmd
1 Replies
8. Filesystems, Disks and Memory
Recently added a disk to a clariion array system, binded it as a raid 5, now I have no clue how to see it in dg-unix. I want to add it to a current filesystem, and now i'm down river without a paddle. (0 Replies)
Discussion started by: danceofillusion
0 Replies
9. SCO
hi
I've a fresh installation of SCO 5.0.7 on the IDE hard disk.
For SCSI hard disk I can declare, for example blc disk driver using:
# mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Discussion started by: ccc
3 Replies
10. AIX
Hi,
On P5 I would like to add hard drive, currently 2 hard disk are already exists, would like to add one more,
2 Slots are emtpy, I would like to know how to find out wheather adapter is attached to that 2 free slot using command. (7 Replies)
Discussion started by: manoj.solaris
7 Replies
SD(4) Linux Programmer's Manual SD(4)
NAME
sd - driver for SCSI disk drives
SYNOPSIS
#include <linux/hdreg.h> /* for HDIO_GETGEO */
#include <linux/fs.h> /* for BLKGETSIZE and BLKRRPART */
CONFIGURATION
The block device name has the following form: sdlp, where l is a letter denoting the physical drive, and p is a number denoting the parti-
tion on that physical drive. Often, the partition number, p, will be left off when the device corresponds to the whole drive.
SCSI disks have a major device number of 8, and a minor device number of the form (16 * drive_number) + partition_number, where drive_num-
ber is the number of the physical drive in order of detection, and partition_number is as follows:
partition 0 is the whole drive
partitions 1-4 are the DOS "primary" partitions
partitions 5-8 are the DOS "extended" (or "logical") partitions
For example, /dev/sda will have major 8, minor 0, and will refer to all of the first SCSI drive in the system; and /dev/sdb3 will have
major 8, minor 19, and will refer to the third DOS "primary" partition on the second SCSI drive in the system.
At this time, only block devices are provided. Raw devices have not yet been implemented.
DESCRIPTION
The following ioctls are provided:
HDIO_GETGEO
Returns the BIOS disk parameters in the following structure:
struct hd_geometry {
unsigned char heads;
unsigned char sectors;
unsigned short cylinders;
unsigned long start;
};
A pointer to this structure is passed as the ioctl(2) parameter.
The information returned in the parameter is the disk geometry of the drive as understood by DOS! This geometry is not the physical
geometry of the drive. It is used when constructing the drive's partition table, however, and is needed for convenient operation of
fdisk(1), efdisk(1), and lilo(1). If the geometry information is not available, zero will be returned for all of the parameters.
BLKGETSIZE
Returns the device size in sectors. The ioctl(2) parameter should be a pointer to a long.
BLKRRPART
Forces a reread of the SCSI disk partition tables. No parameter is needed.
The SCSI ioctl(2) operations are also supported. If the ioctl(2) parameter is required, and it is NULL, then ioctl(2) will fail
with the error EINVAL.
FILES
/dev/sd[a-h]: the whole device
/dev/sd[a-h][0-8]: individual block partitions
COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 2012-05-03 SD(4)