12-27-2008
First update your firmware to latest levels (if you haven't already).
IBM Entry Level Disk Storage: Overview - IBM System Storage
You'll need to install the SMclient software on a machine connected to the array. Often times this is a machine connected out-of-band directly to the ethernet mgmt port of the storage array... but I believe the software can send messages via the fibre HBA (in some cases) to communicate with the unit. You'll have to look at the compatibility matrix from IBM to determine if you have the right pieces for that... so I recommend that you do the out-of-band option.
Read all about it from the Redbook at:
IBM Redbooks | IBM System Storage DS3000: Introduction and Implementation Guide
I might have access to one of these devices at the office, but it's likely we've got it configured with some other kind of proprietary IBM sw... (let's just say IBM doesn't get a "user friendly" award in this case).
Anyway, assuming you can get a Windows or Linux host connected to the out-of-band ethernet port of the DS3000 and get the Storage Manger sw installed (SMclient), then from that interface you can configure LUNs, etc.
HTH,
Chris
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi there,
does anybody knows/info on compatiblity on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server.
Regards. (0 Replies)
Discussion started by: gagasan_makmur
0 Replies
2. Solaris
Hello,
I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9).
Who have already done this and can give me the procedure to follow ?
driver to install
multipath
etc...
Thanks in advance
Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies
3. UNIX for Advanced & Expert Users
Hello!
I'm having problems to install Emulex fibrechannel card drivers to a HP DL580 G5 running Solaris 10 x86_64. Any of you guys had this problem or knows the answer? =)
cfgadm gives me the following info, which seems to say that it is ok?
But the card has'nt logged into the switch... (0 Replies)
Discussion started by: Esaia
0 Replies
4. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
5. Solaris
Helo experts
What is an HBA? How can i know about that on any server?
Thanx in advance... (7 Replies)
Discussion started by: younus_syed
7 Replies
6. Solaris
Hi,
I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings.
Do I need... (6 Replies)
Discussion started by: gwhelan
6 Replies
7. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
8. Filesystems, Disks and Memory
Hope I'm in the right place. I'm in the process of zoning HBA's to my new library environment. Is there a "rule of thumb" for the number of physical tape drives that you zone to an HBA? I don't want to run the risk of overloading an HBA. Any information would be greatly appreciated. Thanks. (2 Replies)
Discussion started by: jwholey
2 Replies
9. Solaris
Hi,
I have a HBA that is currently offline for some unknown reason. The device shows up in the prtdiag -v stating it is okay. How can I bring this back online? It was working okay until recently. It is currently connected to the SAN. Details below.
# fcinfo hba-port
HBA Port WWN:... (7 Replies)
Discussion started by: sparcman
7 Replies
10. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
LEARN ABOUT DEBIAN
fs_wscell
FS_WSCELL(1) AFS Command Reference FS_WSCELL(1)
NAME
fs_wscell - Returns the name of the cell to which a machine belongs
SYNOPSIS
fs wscell [-help]
fs ws [-h]
DESCRIPTION
The fs wscell command returns the name of the local machine's home cell.
OPTIONS
-help
Prints the online help for this command. All other valid options are ignored.
OUTPUT
The output displays the contents of the local /etc/openafs/ThisCell file, in the format
This workstation belongs to cell '<cellname>'
EXAMPLES
The following example results when the fs wscell is issued on a machine in the State University cell:
% fs wscell
This workstation belongs to cell 'stateu.edu'
PRIVILEGE REQUIRED
None
SEE ALSO
fs_whereis(1), fs_whichcell(1)
COPYRIGHT
IBM Corporation 2000. <http://www.ibm.com/> All Rights Reserved.
This documentation is covered by the IBM Public License Version 1.0. It was converted from HTML to POD by software written by Chas
Williams and Russ Allbery, based on work by Alf Wachsmann and Elizabeth Cassell.
OpenAFS 2012-03-26 FS_WSCELL(1)