Sponsored Content
Full Discussion: openSuse 10.3 , Emulex HBA
Top Forums UNIX for Advanced & Expert Users openSuse 10.3 , Emulex HBA Post 302271762 by cjcox on Saturday 27th of December 2008 10:19:09 PM
Old 12-27-2008
First update your firmware to latest levels (if you haven't already).

IBM Entry Level Disk Storage: Overview - IBM System Storage


You'll need to install the SMclient software on a machine connected to the array. Often times this is a machine connected out-of-band directly to the ethernet mgmt port of the storage array... but I believe the software can send messages via the fibre HBA (in some cases) to communicate with the unit. You'll have to look at the compatibility matrix from IBM to determine if you have the right pieces for that... so I recommend that you do the out-of-band option.

Read all about it from the Redbook at:
IBM Redbooks | IBM System Storage DS3000: Introduction and Implementation Guide

I might have access to one of these devices at the office, but it's likely we've got it configured with some other kind of proprietary IBM sw... (let's just say IBM doesn't get a "user friendly" award in this case).

Anyway, assuming you can get a Windows or Linux host connected to the out-of-band ethernet port of the DS3000 and get the Storage Manger sw installed (SMclient), then from that interface you can configure LUNs, etc.

HTH,
Chris
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

HBA compatible on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server.

Hi there, does anybody knows/info on compatiblity on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server. Regards. (0 Replies)
Discussion started by: gagasan_makmur
0 Replies

2. Solaris

emulex card on solaris 9

Hello, I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9). Who have already done this and can give me the procedure to follow ? driver to install multipath etc... Thanks in advance Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies

3. UNIX for Advanced & Expert Users

Solaris 10 x86_64 - Emulex Fibrechannel drivers

Hello! I'm having problems to install Emulex fibrechannel card drivers to a HP DL580 G5 running Solaris 10 x86_64. Any of you guys had this problem or knows the answer? =) cfgadm gives me the following info, which seems to say that it is ok? But the card has'nt logged into the switch... (0 Replies)
Discussion started by: Esaia
0 Replies

4. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies

5. Solaris

What is an HBA..?

Helo experts What is an HBA? How can i know about that on any server? Thanx in advance... (7 Replies)
Discussion started by: younus_syed
7 Replies

6. Solaris

Connect Solaris 10 to NetApp filer using Emulex single port HBAs.

Hi, I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings. Do I need... (6 Replies)
Discussion started by: gwhelan
6 Replies

7. AIX

Need HBA card driver

Hi All, SUN emulex HBA card has been installed on P520 box. When i run the cfgmgr i am getting the following message. lpar2#cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies

8. Filesystems, Disks and Memory

HBA performance

Hope I'm in the right place. I'm in the process of zoning HBA's to my new library environment. Is there a "rule of thumb" for the number of physical tape drives that you zone to an HBA? I don't want to run the risk of overloading an HBA. Any information would be greatly appreciated. Thanks. (2 Replies)
Discussion started by: jwholey
2 Replies

9. Solaris

Offline HBA.

Hi, I have a HBA that is currently offline for some unknown reason. The device shows up in the prtdiag -v stating it is okay. How can I bring this back online? It was working okay until recently. It is currently connected to the SAN. Details below. # fcinfo hba-port HBA Port WWN:... (7 Replies)
Discussion started by: sparcman
7 Replies

10. Solaris

How to enable hba port of a two port hba card

Hi, i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port. ---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ---------- please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
FS_MESSAGES(1)						       AFS Command Reference						    FS_MESSAGES(1)

NAME
fs_messages - Sets whether the Cache Manager writes log messages SYNOPSIS
fs messages [-show (user|console|all|none)] [-help] fs me [-s (user|console|all|none)] [-h] DESCRIPTION
The fs messages command controls whether the Cache Manager displays status and warning messages on user screens, the client machine console, on both, or on neither. There are two types of Cache Manager messages: o User messages provide user-level status and warning information, and the Cache Manager directs them to user screens. o Console messages provide system-level status and warning information, and the Cache Manager directs them to the client machine's designated console. Disabling messaging completely is not recommended, because the messages provide useful status and warning information. OPTIONS
-show (user|console|all|none) Specifies the types of messages to display. Choose one of the following values: user Send user messages to user screens. console Send console messages to the console. all Send user messages to user screens and console messages to the console (the default if the -show argument is omitted). none Do not send any messages to user screens or the console. -help Prints the online help for this command. All other valid options are ignored. EXAMPLES
The following command instructs the Cache Manager to display both types of messages: % fs messages -show all PRIVILEGE REQUIRED
The issuer must be logged in as the local superuser root. SEE ALSO
afsd(8) COPYRIGHT
IBM Corporation 2000. <http://www.ibm.com/> All Rights Reserved. This documentation is covered by the IBM Public License Version 1.0. It was converted from HTML to POD by software written by Chas Williams and Russ Allbery, based on work by Alf Wachsmann and Elizabeth Cassell. OpenAFS 2012-03-26 FS_MESSAGES(1)
All times are GMT -4. The time now is 12:35 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy