Sponsored Content
Full Discussion: openSuse 10.3 , Emulex HBA
Top Forums UNIX for Advanced & Expert Users openSuse 10.3 , Emulex HBA Post 302271202 by nux007 on Wednesday 24th of December 2008 08:22:29 AM
Old 12-24-2008
Haven't created LUN

I didn't create the LUN. How can i create it ?
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

HBA compatible on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server.

Hi there, does anybody knows/info on compatiblity on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server. Regards. (0 Replies)
Discussion started by: gagasan_makmur
0 Replies

2. Solaris

emulex card on solaris 9

Hello, I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9). Who have already done this and can give me the procedure to follow ? driver to install multipath etc... Thanks in advance Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies

3. UNIX for Advanced & Expert Users

Solaris 10 x86_64 - Emulex Fibrechannel drivers

Hello! I'm having problems to install Emulex fibrechannel card drivers to a HP DL580 G5 running Solaris 10 x86_64. Any of you guys had this problem or knows the answer? =) cfgadm gives me the following info, which seems to say that it is ok? But the card has'nt logged into the switch... (0 Replies)
Discussion started by: Esaia
0 Replies

4. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies

5. Solaris

What is an HBA..?

Helo experts What is an HBA? How can i know about that on any server? Thanx in advance... (7 Replies)
Discussion started by: younus_syed
7 Replies

6. Solaris

Connect Solaris 10 to NetApp filer using Emulex single port HBAs.

Hi, I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings. Do I need... (6 Replies)
Discussion started by: gwhelan
6 Replies

7. AIX

Need HBA card driver

Hi All, SUN emulex HBA card has been installed on P520 box. When i run the cfgmgr i am getting the following message. lpar2#cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies

8. Filesystems, Disks and Memory

HBA performance

Hope I'm in the right place. I'm in the process of zoning HBA's to my new library environment. Is there a "rule of thumb" for the number of physical tape drives that you zone to an HBA? I don't want to run the risk of overloading an HBA. Any information would be greatly appreciated. Thanks. (2 Replies)
Discussion started by: jwholey
2 Replies

9. Solaris

Offline HBA.

Hi, I have a HBA that is currently offline for some unknown reason. The device shows up in the prtdiag -v stating it is okay. How can I bring this back online? It was working okay until recently. It is currently connected to the SAN. Details below. # fcinfo hba-port HBA Port WWN:... (7 Replies)
Discussion started by: sparcman
7 Replies

10. Solaris

How to enable hba port of a two port hba card

Hi, i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port. ---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ---------- please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
OCE(4)							   BSD Kernel Interfaces Manual 						    OCE(4)

NAME
oce -- Device driver for Emulex OneConnect 10Gb network adapters SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device pci device oce Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_oce_load="YES" DESCRIPTION
Emulex OneConnect adapters come in various skews and with different combinations of NIC, FCoE and iSCSI functions. The oce driver claims the NIC functions in all these adapters. The oce driver supports VLAN Hardware offload, TCP checksum offload, TCP segmentation offload (TSO), Large receive offload (LRO), Bonding, Jumbo frames (from 1500 - 9000), Multiple TX queues, Receive-Side Scaling (RSS) and MSI-X interrupts. HARDWARE
The oce driver supports the following network adapters: o Emulex BladeEngine 2 o Emulex BladeEngine 3 o Emulex Lancer UPDATING FIRMWARE
Adapter firmware updates are persistent. Firmware can be updated by following the steps below: 1. Copy the below code to a Makefile: KMOD=elxflash FIRMWS=imagename.ufi:elxflash .include <bsd.kmod.mk> 2. Replace imagename in above with UFI file name 3. Copy Makefile and UFI file to a directory 4. Execute make & copy generated elxflash.ko to /lib/modules 5. sysctl dev.oce.<if_id>.fw_upgrade=elxflash 6. Reboot the machine In case of issues with supplied UFI, flashing fails with one of the following errors. 1. "Invalid BE3 firmware image" 2. "Invalid Cookie. Firmware image corrupted ?" 3. "cmd to write to flash rom failed." SUPPORT
For general information and support, go to the Emulex website at: http://www.Emulex.com/ or E-Mail at freebsd-drivers@emulex.com. SEE ALSO
ifconfig(8) AUTHORS
The oce driver was written by freebsd-drivers@emulex.com. BSD
February 19, 2012 BSD
All times are GMT -4. The time now is 08:22 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy