12-24-2008
Haven't created LUN
I didn't create the LUN. How can i create it ?
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi there,
does anybody knows/info on compatiblity on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server.
Regards. (0 Replies)
Discussion started by: gagasan_makmur
0 Replies
2. Solaris
Hello,
I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9).
Who have already done this and can give me the procedure to follow ?
driver to install
multipath
etc...
Thanks in advance
Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies
3. UNIX for Advanced & Expert Users
Hello!
I'm having problems to install Emulex fibrechannel card drivers to a HP DL580 G5 running Solaris 10 x86_64. Any of you guys had this problem or knows the answer? =)
cfgadm gives me the following info, which seems to say that it is ok?
But the card has'nt logged into the switch... (0 Replies)
Discussion started by: Esaia
0 Replies
4. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
5. Solaris
Helo experts
What is an HBA? How can i know about that on any server?
Thanx in advance... (7 Replies)
Discussion started by: younus_syed
7 Replies
6. Solaris
Hi,
I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings.
Do I need... (6 Replies)
Discussion started by: gwhelan
6 Replies
7. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
8. Filesystems, Disks and Memory
Hope I'm in the right place. I'm in the process of zoning HBA's to my new library environment. Is there a "rule of thumb" for the number of physical tape drives that you zone to an HBA? I don't want to run the risk of overloading an HBA. Any information would be greatly appreciated. Thanks. (2 Replies)
Discussion started by: jwholey
2 Replies
9. Solaris
Hi,
I have a HBA that is currently offline for some unknown reason. The device shows up in the prtdiag -v stating it is okay. How can I bring this back online? It was working okay until recently. It is currently connected to the SAN. Details below.
# fcinfo hba-port
HBA Port WWN:... (7 Replies)
Discussion started by: sparcman
7 Replies
10. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
format(1M) format(1M)
NAME
format - format an HP SCSI disk array LUN
SYNOPSIS
device_file
DESCRIPTION
formats one LUN of the HP SCSI disk array associated with device file, device_file. The format will usually be a soft or zeroing format,
in which the controller writes zeroes to the data area and parity area, if any, of the LUN.
NOTE: The above should always be true of a sub-LUN, but the controller might decide, based on certain conditions, to do a full format of a
regular LUN, which consists of sending a mode select and a media initialization command to the physical drive(s) in question, fol-
lowed by zeroing the data and parity area, if any. The conditions which will cause a full format to be done are as follows:
1. The controller received a Mode Select command which requires a drive sector size change.
2. The controller received a Mode Select command which changed a parameter in the Format Device Page(0x03).
3. The LUN contains one or more failed drives. In this case only a certain subset of the drives containing the failed drives
will be formatted.
4. Either the FmtData or the CmpLst bit in the Format Unit CDB is set.
RETURN VALUE
returns the following values:
0 Successful completion.
-1 Command failed.
DIAGNOSTICS AND ERRORS
Errors can originate from problems with:
o
o SCSI (device level) communications
o system calls
Error messages generated by format:
An error in command syntax has occurred.
Enter command again with all required arguments, in the order shown.
To ensure that
does not modify a disk array that is being used by another process, attempts to obtain exclusive access to the disk array. If the
disk array is already opened by another process (for example, LVM -- the Logical Volume Manager), a "" error message is returned by
the driver. To eliminate the "" condition, determine what process has the device open. In the case of LVM, it is necessary to
deactivate the volume group containing the array before formatting array LUNs (see vgchange(1M)).
The LUN number, which is derived from the device file name, is out of range.
The addressed LUN
is not configured, and thus is not known to the array controller.
Utilities must be able to open the device file for raw access.
The device being addressed is not an HP SCSI disk array.
SCSI (device level) communication errors:
Sense data associated with the failed operation is printed.
Error messages generated by system calls:
uses the following system calls:
and
Documentation for these HP-UX system calls contains information about the specific error conditions associated with each call. does not
alter the value of The interpretation of for printing purposes is performed by the system utility
EXAMPLES
To format the HP SCSI disk array LUN on a Series 800:
WARNING
The command will destroy all user data on the addressed LUN.
DEPENDENCIES
The HP C2425 and HP C2427 disk arrays are only supported on Series 700 systems running HP-UX version 9.0X.
The HP C2430 disk array is supported on Series 700 and 800 systems running HP-UX versions 9.0X and 10.0X.
AUTHOR
was developed by HP.
format(1M)