Sponsored Content
Top Forums UNIX for Advanced & Expert Users Sun 6048 Blade Rack Power Reqs. Post 302270958 by bluescreen on Tuesday 23rd of December 2008 09:50:45 AM
Old 12-23-2008
Quote:
Originally Posted by reborg
I don't wish to seem abrupt but if you have a specific question please ask the question rather than related questions. I assume you are asking because you have a fully taken delivery of a pre-racked system?
Thanks for your assistance, reborg. Smilie
 

9 More Discussions You Might Find Interesting

1. Solaris

sun Blade 2000 and XVR100

hello, I have SunBlade 2000 with XVR-1000 graphics card. Xserver won't loaded. I've reinstalled OS 9 ( loaded Driver) nor 10 still won't do it. Anyone has this problem or have any ideas whats' wrong, greatly appreciated!! thanks in adv. (1 Reply)
Discussion started by: anphdula
1 Replies

2. UNIX for Dummies Questions & Answers

Please help to configure Sun Blade 150 workstation

Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies

3. Solaris

Sun Blade 100 Disk Compatibility

It's me again, I was taking my Sun Blade 100 apart last night to see what kind of drive I have. It is a Seagate ST320011A Barracuda ATA IV 20 GB 7200 RPM Ultra ATA/100 IDE. Now 20 gig ain't all that big anymore and I got to thinking about putting a couple bigger drives in there. although I... (7 Replies)
Discussion started by: BrewDudeBob
7 Replies

4. Hardware

Sun Blade 1000 keyboard not detected.

Hello, I have a sun blade 1000 machine, it passes post, has 2 750mhz sparc 3 cpus and has 4GB of ram. I have setup a TIP connection and did everything i could to figure what the hell is going on, but I cannot it seems to me that the usb ports are not giving out any power. I've tried all... (0 Replies)
Discussion started by: binary0x01
0 Replies

5. Solaris

Sun Blade 150 not a Sun?

I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05. I have just noticed /bin/sun now returns false, rather than true. See below. $ uname -a SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100 $ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies

6. UNIX for Dummies Questions & Answers

Reinstalling Solaris 9 on Sun Blade 100

For the past ten years I have owned a blade 100, and I had Solaris 9 running on it. Due to the fact, 9 is woefully out of date, I wanted to try 10, but 10 needed more ram, so I beefed up the ram to the full 2 gig. I have two 15 gig ide drives in the box (stock drives). But unfortunately solaris... (2 Replies)
Discussion started by: RichardET
2 Replies

7. UNIX for Dummies Questions & Answers

SUN BLADE T6340 - which OS ?

Hi, I have server SUN BLADE T6340 and i tried install debian sparc on this machine. Will it work ? In the specification is written only Solaris 10. (4 Replies)
Discussion started by: PtaQ
4 Replies

8. Hardware

How to find Power Management Profile on CLI for Blade?

Hi, I have set the power management profile on a Blade to Max Performance. Is there and command I can run to check this when the machine is up and running Thanks (2 Replies)
Discussion started by: eeisken
2 Replies

9. Solaris

Execution problems with sun blade 150

hello i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
HAMEXAM(1)						      General Commands Manual							HAMEXAM(1)

NAME hamexam - Study guide for USA FCC amateur radio (ham radio) license examinations.
SYNOPSIS
hamexam [option] DESCRIPTION
hamexam presents questions in random order from the selected question pool, and terminates when all questions have been answered correctly. The session may be interrupted with ^C, and resumed later. Some questions refer to diagrams. The diagrams for the selected question pool are displayed in a separate window using eog(1). Licenses are issued by the Federal Communications Commission (FCC), but examinations are administered by Volunteer Examiners. OPTIONS
If no pool is specified, usage, version, and help information is displayed. In normal usage, one of the following options should be specified: t Element 2, the Technician Class pool. This is the entry-level license. g Element 3, the General Class pool (element 2 is also required). e Element 4, the Extra Class pool (elements 2 and 3 are also required). q The question pool is selected interactively. FILES
A directory ~/.hamexam is created to hold the names of the questions which remain to be answered correctly. SEE ALSO
For more information regarding licensing, ref. http://www.arrl.org/licensing-preparation-exams For information regarding the question pools, ref. http://www.ncvec.org/ COPYRIGHT
hamexam is Copyright (c) 2011-2012 John Nogatch <jnogatch@yahoo.com>. This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MER- CHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. BUGS
The question pools are normally good for 4 years, but are sometimes modified; ref. http://www.ncvec.org/ hamexam does not automatically update the question pools from the VEC Web site. HAMEXAM(1)
All times are GMT -4. The time now is 12:40 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy