12-23-2008
Quote:
Originally Posted by
reborg
I don't wish to seem abrupt but if you have a specific question please ask the question rather than related questions. I assume you are asking because you have a fully taken delivery of a pre-racked system?
Thanks for your assistance, reborg.
9 More Discussions You Might Find Interesting
1. Solaris
hello,
I have SunBlade 2000 with XVR-1000 graphics card. Xserver won't loaded. I've reinstalled OS 9 ( loaded Driver) nor 10 still won't do it. Anyone has this problem or have any ideas whats' wrong, greatly appreciated!!
thanks in adv. (1 Reply)
Discussion started by: anphdula
1 Replies
2. UNIX for Dummies Questions & Answers
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies
3. Solaris
It's me again, I was taking my Sun Blade 100 apart last night to see what kind of drive I have. It is a Seagate ST320011A Barracuda ATA IV 20 GB 7200 RPM Ultra ATA/100 IDE.
Now 20 gig ain't all that big anymore and I got to thinking about putting a couple bigger drives in there. although I... (7 Replies)
Discussion started by: BrewDudeBob
7 Replies
4. Hardware
Hello,
I have a sun blade 1000 machine, it passes post, has 2 750mhz sparc 3 cpus and has 4GB of ram.
I have setup a TIP connection and did everything i could to figure what the hell is going on, but I cannot it seems to me that the usb ports are not giving out any power.
I've tried all... (0 Replies)
Discussion started by: binary0x01
0 Replies
5. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
6. UNIX for Dummies Questions & Answers
For the past ten years I have owned a blade 100, and I had Solaris 9 running on it.
Due to the fact, 9 is woefully out of date, I wanted to try 10, but 10 needed more ram, so I beefed up the ram to the full 2 gig. I have two 15 gig ide drives in the box (stock drives). But unfortunately solaris... (2 Replies)
Discussion started by: RichardET
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I have server SUN BLADE T6340 and i tried install debian sparc on this machine.
Will it work ?
In the specification is written only Solaris 10. (4 Replies)
Discussion started by: PtaQ
4 Replies
8. Hardware
Hi,
I have set the power management profile on a Blade to Max Performance.
Is there and command I can run to check this when the machine is up and running
Thanks (2 Replies)
Discussion started by: eeisken
2 Replies
9. Solaris
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
LEARN ABOUT LINUX
debconf-set-selections
DEBCONF-SET-SELECTIONS(1) Debconf DEBCONF-SET-SELECTIONS(1)
NAME
debconf-set-selections - insert new default values into the debconf database
SYNOPSIS
debconf-set-selections file
debconf-get-selections | ssh newhost debconf-set-selections
DESCRIPTION
debconf-set-selections can be used to pre-seed the debconf database with answers, or to change answers in the database. Each question will
be marked as seen to prevent debconf from asking the question interactively.
Reads from a file if a filename is given, otherwise from stdin.
WARNING
Only use this command to seed debconf values for packages that will be or are installed. Otherwise you can end up with values in the
database for uninstalled packages that will not go away, or with worse problems involving shared values. It is recommended that this only
be used to seed the database if the originating machine has an identical install.
DATA FORMAT
The data is a series of lines. Lines beginning with a # character are comments. Blank lines are ignored. All other lines set the value of
one question, and should contain four values, each separated by one character of whitespace. The first value is the name of the package
that owns the question. The second is the name of the question, the third value is the type of this question, and the fourth value (through
the end of the line) is the value to use for the answer of the question.
Alternatively, the third value can be "seen"; then the preseed line only controls whether the question is marked as seen in debconf's
database. Note that preseeding a question's value defaults to marking that question as seen, so to override the default value without
marking a question seen, you need two lines.
Lines can be continued to the next line by ending them with a "" character.
EXAMPLES
# Force debconf priority to critical.
debconf debconf/priority select critical
# Override default frontend to readline, but allow user to select.
debconf debconf/frontend select readline
debconf debconf/frontend seen false
OPTIONS
--verbose, -v
verbose output
--checkonly, -c
only check the input file format, do not save changes to database
SEE ALSO
debconf-get-selections(1) (available in the debconf-utils package)
AUTHOR
Petter Reinholdtsen <pere@hungry.com>
2011-06-22 DEBCONF-SET-SELECTIONS(1)