12-22-2008
I have seen this many times, and I agree its a DNS issue.
10 More Discussions You Might Find Interesting
1. BSD
just as the title says.
thanks.
#General Rule Sets
/sbin/ipfw add 0300 check-state
/sbin/ipfw add 0301 deny tcp from any to any in established
/sbin/ipfw add 0302 pass tcp from any to any out setup keep-state
/sbin/ipfw add 0303 pass udp from any to any out
#SSH FTP
/sbin/ipfw add 0400... (11 Replies)
Discussion started by: dwildgoose
11 Replies
2. Solaris
When I ssh to my box, an Ultra 5. I get prompted for password immediately. I enter it and have to wait sometimes a full minute for it to prompt for a password.
The same thing happens when i try to ftp to the box, it will say connected, but it takes forever to prompt for password, and... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
3. UNIX for Dummies Questions & Answers
Hi again guys,
Earlier today, just all of a sudden, all SSH and FTP connections to my internal Linux box just slowed down to a crawl. After the connection/authentication though, everything was back to normal speed. Until you have to connect again. A box reboot didnt work either.
Now, from... (1 Reply)
Discussion started by: Aeros
1 Replies
4. Solaris
Hi Guys and Girls, I know this is a common question but I've searched and we've tried the suggestions without luck. When I log into the box via SSH from a windows machine I get a 1 min 20 sec delay. If we add my IP address and machine name to /etc/hosts then I get an instant login. I would be happy... (12 Replies)
Discussion started by: MikeKulls
12 Replies
5. Shell Programming and Scripting
I have some sample code that's supposed to ssh to another machine using Net::SSH::Perl, execute a command, and print
the output of that command. It's very basic, and it works. However, I noticed that upon logging in:
$ssh->login('username','password');
It takes roughly 10-13 seconds to... (2 Replies)
Discussion started by: mrwatkin
2 Replies
6. Solaris
I have Solaris-10 server which was patched by patch cluster last weekend. After patching, it connects slow with other server. Meaning, when I do -
ssh server2
OR
ssh wluser2@server2
OR
ssh root@server2
It waits for 9-10 seconds and then prompt for password, while it used to be instant... (2 Replies)
Discussion started by: solaris_1977
2 Replies
7. Solaris
Hi, I have the following issue, when I tried to login to an Openindiana remote server through ssh It takes to long to ask me for the password. So i tried -v and I realize that sshd hangs here " debug1: SSH2_MSG_SERVICE_ACCEPT received " for at least 2 minutes. Then I can log in and everything is... (2 Replies)
Discussion started by: piukeman
2 Replies
8. HP-UX
Hi experts,
We are getting slow ssh session connections at HP-UX 11.31 servers.
We have set the parameters that maybe will affect , and commented at other theads at config file sshd_config :
UseDNS no
X11Forwarding yes
X11DisplayOffset 10
X11UseLocalhost no
GSSAPIAuthentication no.
... (7 Replies)
Discussion started by: SapBasisSystem
7 Replies
9. SuSE
We are having an issue with slow password prompts via SSH login on all of our SLES 11.2 boxes. The output from a ssh -v login attempt shows a delay here:
debug1: SSH2_MSG_SERVICE_ACCEPT receivedThis issue only happens on the first logon of the day; subsequent logons are normal. Adding the client's... (8 Replies)
Discussion started by: j_aix
8 Replies
10. Solaris
ssh is slow on solaris zone , and is getting stuck at the following place.
debug2: callback done
debug2: channel 0: open confirm rwindow 0 rmax 32768
debug3: Wrote 664 bytes for a total of 3325
Below is the ssh version being used: Sun_SSH_1.1.6, SSH protocols 1.5/2.0, OpenSSL 0x0090704f
... (10 Replies)
Discussion started by: skamal4u
10 Replies
LEARN ABOUT MOJAVE
mail::dkim::dns
Mail::DKIM::DNS(3) User Contributed Perl Documentation Mail::DKIM::DNS(3)
NAME
Mail::DKIM::DNS - performs DNS queries for Mail::DKIM
DESCRIPTION
This is the module that performs DNS queries for Mail::DKIM.
CONFIGURATION
This module has a couple configuration settings that the caller may want to use to customize the behavior of this module.
$Mail::DKIM::DNS::TIMEOUT
This global variable specifies the maximum amount of time (in seconds) to wait for a single DNS query to complete. The default is 10.
Mail::DKIM::DNS::resolver()
Use this global subroutine to get or replace the instance of Net::DNS::Resolver that Mail::DKIM uses. If set to undef (the default), then a
brand new default instance of Net::DNS::Resolver will be created the first time a DNS query is needed.
You will call this subroutine if you want to specify non-default options to Net::DNS::Resolver, such as different timeouts, or to enable
use of a persistent socket. For example:
# first, construct a custom DNS resolver
my $res = Net::DNS::Resolver->new(
udp_timeout => 3, tcp_timeout => 3, retry => 2,
);
$res->udppacketsize(1240);
$res->persistent_udp(1);
# then, tell Mail::DKIM to use this resolver
Mail::DKIM::DNS::resolver($res);
Mail::DKIM::DNS::enable_EDNS0()
This is a convenience subroutine that will construct an appropriate DNS resolver that uses EDNS0 (Extension mechanisms for DNS) to support
large DNS replies, and configure Mail::DKIM to use it. (As such, it should NOT be used in conjunction with the resolver() subroutine
described above.)
Mail::DKIM::DNS::enable_EDNS0();
Use of EDNS0 is recommended, since it reduces the need for falling back to TCP when dealing with large DNS packets. However, it is not
enabled by default because some Internet firewalls which do deep inspection of packets are not able to process EDNS0-enabled packets. When
there is a firewall on a path to a DNS resolver, the EDNS0 feature should be specifically tested before enabling.
AUTHOR
Jason Long, <jlong@messiah.edu>
COPYRIGHT AND LICENSE
Copyright (C) 2006-2007, 2012-2013 by Messiah College
This library is free software; you can redistribute it and/or modify it under the same terms as Perl itself, either Perl version 5.8.6 or,
at your option, any later version of Perl 5 you may have available.
perl v5.18.2 2013-02-07 Mail::DKIM::DNS(3)