Sponsored Content
Operating Systems Solaris Disable Inbuilt multipathing software of Solaris 10 Post 302270197 by girish.batra on Saturday 20th of December 2008 04:23:11 AM
Old 12-20-2008
Thanks from the bottom of heart reborg
 

10 More Discussions You Might Find Interesting

1. IP Networking

Quick Poll: Solaris IP Multipathing

I've setup Solaris IP Multipathing under Solaris whenever the hardware to do so was available. I find it amazing though that so few places I've worked at don't use it until I arrive. I wanted to find out if I'm running into all the exceptions, or is it really not being used? ... (3 Replies)
Discussion started by: kduffin
3 Replies

2. Solaris

disable telnet on Solaris

All - would you please some one help me to disable telnet on Solaris? /etc/inetd.conf Thanks :confused: (11 Replies)
Discussion started by: March_2007
11 Replies

3. Solaris

solaris multipathing

I have solaris 10 sparc. I installed a Qlogic hba card. This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay. I formated 2 luns. On my solaris system, i have 4 disk. How to configure solaris 10 to fix the dual disk view. ... (4 Replies)
Discussion started by: simquest
4 Replies

4. Solaris

Solaris IP Multipathing (IPMP) Help

Hello All, I work for a Health care company at a local trauma hospital. I maintain a Picture Archiving and Communication System (PAC's). Basically, any medical images (X-Ray, CT, MRI, Mammo, etc) are stored digitally on the servers for viewing and dictation from diagnostic stations. I took over... (10 Replies)
Discussion started by: mainegeek
10 Replies

5. Solaris

Solaris IP Multipathing

Hi, I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation . I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2. Now is it possible to have IP Multipathing on each of the servers as follows ? ... (0 Replies)
Discussion started by: maadhuu
0 Replies

6. Solaris

Solaris multipathing

Hai we using emc storage which is conneted to M5000 through san switch. we asign 13 luns but in server it is showing 22 luns. i enable the solaris multipathing (MPxIO) #more /kernel/drv/fp.conf in that file MPxio-disable=no #mpathadm list lu it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies

7. Solaris

Disable all the logs in Solaris

Hi Is there anyway to disable all logs/logging (lastlog, sulog, messages etc.) in Solaris 9&10? I know this is not recommended but i just want to know if this is possible. TIA Reddy (8 Replies)
Discussion started by: reddyr
8 Replies

8. Solaris

Solaris 11 disable IPv6

I've new installed Solaris 11 on Sparc T4-1. I'd like to disable IPv6 but with no luck. lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2 inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies

9. Solaris

ZeusIOPS multipathing failed Solaris 11

hi, just installed solaris 11.1 (11.1.9.5.1) on a sun7410 ZFSSA (x4440 + j4400), but when I enable multipathing with "stmsboot -e", only the 1TB SATA drives inside the j4400 are configured as multipathed vhci / mpxio devices, but the logzillas / ZeusIOPS drives are skipped. the server is... (0 Replies)
Discussion started by: pressy
0 Replies

10. Solaris

Can't disable CPU in Solaris

hello all i have an issue about a solaris V440 cpu, im logged in the Ok prompt i can't disable a CPU3, i can't see it in dev list, i see only the cpu3-bank0 to cpu-bank4 please help me to disable it thank youuu (3 Replies)
Discussion started by: walidadam
3 Replies
Graphics::Primitive::Insets(3pm)			User Contributed Perl Documentation			  Graphics::Primitive::Insets(3pm)

NAME
Graphics::Primitive::Insets - Space between things DESCRIPTION
Graphics::Primitive::Insets represents the amount of space that surrounds something. This object can be used to represent either padding or margins (in the CSS sense, one being inside the bounding box, the other being outside) SYNOPSIS
use Graphics::Primitive::Insets; my $insets = Graphics::Primitive::Insets->new({ top => 5, bottom => 5, left => 5, right => 5 }); METHODS
Constructor new Creates a new Graphics::Primitive::Insets. Instance Methods as_array Return these insets as an array in the form of top, right, bottom and left. bottom Set/Get the inset from the bottom. equal_to Determine if these Insets are equal to another. left Set/Get the inset from the left. right Set/Get the inset from the right. top Set/Get the inset from the top. zero Sets all the insets (top, left, bottom, right) to 0. AUTHOR
Cory Watson, "<gphat@cpan.org>" SEE ALSO
perl(1) COPYRIGHT &; LICENSE Copyright 2008-2010 by Cory G Watson. This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself. perl v5.12.3 2010-08-21 Graphics::Primitive::Insets(3pm)
All times are GMT -4. The time now is 09:10 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy