Sponsored Content
Full Discussion: openSuse 10.3 , Emulex HBA
Top Forums UNIX for Advanced & Expert Users openSuse 10.3 , Emulex HBA Post 302269845 by cjcox on Thursday 18th of December 2008 07:37:29 PM
Old 12-18-2008
Have you created a LUN on the storage array? Has it been masked (or unmasked) appropriately so your fibre HBA can see it? If so, if doing this dynamically, have you run:

rescan-scsi-bus.sh -w -l

as root on your linux host?

You can do lsscsi to see what devices can be seen afterwards.
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

HBA compatible on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server.

Hi there, does anybody knows/info on compatiblity on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server. Regards. (0 Replies)
Discussion started by: gagasan_makmur
0 Replies

2. Solaris

emulex card on solaris 9

Hello, I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9). Who have already done this and can give me the procedure to follow ? driver to install multipath etc... Thanks in advance Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies

3. UNIX for Advanced & Expert Users

Solaris 10 x86_64 - Emulex Fibrechannel drivers

Hello! I'm having problems to install Emulex fibrechannel card drivers to a HP DL580 G5 running Solaris 10 x86_64. Any of you guys had this problem or knows the answer? =) cfgadm gives me the following info, which seems to say that it is ok? But the card has'nt logged into the switch... (0 Replies)
Discussion started by: Esaia
0 Replies

4. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies

5. Solaris

What is an HBA..?

Helo experts What is an HBA? How can i know about that on any server? Thanx in advance... (7 Replies)
Discussion started by: younus_syed
7 Replies

6. Solaris

Connect Solaris 10 to NetApp filer using Emulex single port HBAs.

Hi, I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings. Do I need... (6 Replies)
Discussion started by: gwhelan
6 Replies

7. AIX

Need HBA card driver

Hi All, SUN emulex HBA card has been installed on P520 box. When i run the cfgmgr i am getting the following message. lpar2#cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies

8. Filesystems, Disks and Memory

HBA performance

Hope I'm in the right place. I'm in the process of zoning HBA's to my new library environment. Is there a "rule of thumb" for the number of physical tape drives that you zone to an HBA? I don't want to run the risk of overloading an HBA. Any information would be greatly appreciated. Thanks. (2 Replies)
Discussion started by: jwholey
2 Replies

9. Solaris

Offline HBA.

Hi, I have a HBA that is currently offline for some unknown reason. The device shows up in the prtdiag -v stating it is okay. How can I bring this back online? It was working okay until recently. It is currently connected to the SAN. Details below. # fcinfo hba-port HBA Port WWN:... (7 Replies)
Discussion started by: sparcman
7 Replies

10. Solaris

How to enable hba port of a two port hba card

Hi, i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port. ---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ---------- please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
tran_bus_reset(9e)						Driver Entry Points						tran_bus_reset(9e)

NAME
tran_bus_reset - reset a SCSI bus SYNOPSIS
#include <sys/scsi/scsi.h> int prefix tran_bus_reset(dev_info_t *hba_dip, int level); INTERFACE LEVEL
Solaris DDI PARAMETERS
hba_dip The dev_info_t pointer associated with the SCSI HBA. level The level of reset required. DESCRIPTION
The tran_bus_reset() vector in the scsi_hba_tran(9S) structure should be initialized during the HBA driver's attach(9E). It is an HBA entry point to be called when a user initiates a bus reset through device control interfaces. tran_bus_reset() must reset the SCSI bus without resetting targets. level will be one of the following: RESET_BUS Reset the SCSI bus only, not the targets. Implementation is hardware specific. If it is not possible to reset the SCSI bus without changing the state and operating mode of the tar- gets, the HBA driver should not initialize this vector or return failure. RETURN VALUES
tran_bus_reset() should return: 1 on success. 0 on failure. ATTRIBUTES
See attributes(5) for a description of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | |Stability Level |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
attributes(5), tran_quiesce(9E), scsi_hba_tran(9S) SunOS 5.10 17 Mar 1999 tran_bus_reset(9e)
All times are GMT -4. The time now is 07:52 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy