12-18-2008
Have you created a LUN on the storage array? Has it been masked (or unmasked) appropriately so your fibre HBA can see it? If so, if doing this dynamically, have you run:
rescan-scsi-bus.sh -w -l
as root on your linux host?
You can do lsscsi to see what devices can be seen afterwards.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi there,
does anybody knows/info on compatiblity on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server.
Regards. (0 Replies)
Discussion started by: gagasan_makmur
0 Replies
2. Solaris
Hello,
I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9).
Who have already done this and can give me the procedure to follow ?
driver to install
multipath
etc...
Thanks in advance
Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies
3. UNIX for Advanced & Expert Users
Hello!
I'm having problems to install Emulex fibrechannel card drivers to a HP DL580 G5 running Solaris 10 x86_64. Any of you guys had this problem or knows the answer? =)
cfgadm gives me the following info, which seems to say that it is ok?
But the card has'nt logged into the switch... (0 Replies)
Discussion started by: Esaia
0 Replies
4. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
5. Solaris
Helo experts
What is an HBA? How can i know about that on any server?
Thanx in advance... (7 Replies)
Discussion started by: younus_syed
7 Replies
6. Solaris
Hi,
I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings.
Do I need... (6 Replies)
Discussion started by: gwhelan
6 Replies
7. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
8. Filesystems, Disks and Memory
Hope I'm in the right place. I'm in the process of zoning HBA's to my new library environment. Is there a "rule of thumb" for the number of physical tape drives that you zone to an HBA? I don't want to run the risk of overloading an HBA. Any information would be greatly appreciated. Thanks. (2 Replies)
Discussion started by: jwholey
2 Replies
9. Solaris
Hi,
I have a HBA that is currently offline for some unknown reason. The device shows up in the prtdiag -v stating it is okay. How can I bring this back online? It was working okay until recently. It is currently connected to the SAN. Details below.
# fcinfo hba-port
HBA Port WWN:... (7 Replies)
Discussion started by: sparcman
7 Replies
10. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
ESP(4) BSD Kernel Interfaces Manual ESP(4)
NAME
esp -- Emulex ESP, NCR 53C9x and QLogic FAS families based SCSI controllers
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device esp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_esp_load="YES"
DESCRIPTION
The esp driver provides support for the AMD Am53C974, the Emulex ESP100, ESP100A, ESP200 and ESP406, the NCR 53C90, 53C94 and 53C96 as well
as the QLogic FAS100A, FAS216, FAS366 and FAS408 SCSI controller chips found in a wide variety of systems and peripheral boards.
HARDWARE
Controllers supported by the esp driver include:
o MELCO IFC-DP (PC-98)
o Sun ESP family
o Sun FAS family
o Tekram DC390
o Tekram DC390T
SEE ALSO
cd(4), ch(4), da(4), intro(4), pci(4), sa(4), sbus(4), scsi(4), camcontrol(8)
HISTORY
The esp driver first appeared in NetBSD 1.3. The first FreeBSD version to include it was FreeBSD 5.3.
AUTHORS
The esp driver was ported to FreeBSD by Scott Long <scottl@FreeBSD.org> and later on considerably improved by Marius Strobl
<marius@FreeBSD.org>.
BUGS
The esp driver should read the EEPROM settings of Tekram controllers.
BSD
November 1, 2011 BSD