12-17-2008
That’s part of multipathing which need to be configure . lookout in form for multipathing .
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello everybody!!
I need your help again.
I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp.
"windu_sm_o aaaa,baaa,caaa,daaa" etc.
I am not able to locate which application is generating these files.
Can I straightway delete these files ? or... (1 Reply)
Discussion started by: vikasdeshmukh
1 Replies
2. UNIX for Advanced & Expert Users
Dear All,
I have trouble, I have SPARC Machine and when start for loading, can not finish !
this is copy off message from my system
Netra t 1120/1125 (UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 512 MB memory installed, Serial #12116535.
Ethernet address 8:0:20:b8:e2:37, Host ID:... (4 Replies)
Discussion started by: heru_90
4 Replies
3. Solaris
I have an ultra sparc 2 with no video - I connect to it with hyperterm.
Is there a way to get to the OK prompt? I have tried control/break and that does not work.
If not is there a video card I can get to put in this box?
I have Solaris 10 installed on this machine.
Thanks (7 Replies)
Discussion started by: tribbles
7 Replies
4. Solaris
Hi Gurus,
Can I use null modem cable in Ultra sparc 10 workstation
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
5. Debian
Comments/Problems:
Machine boots from CDROM, starts SILO Version 1.4.13,
display welcome message (welcome to Debian GNU/Linux lenny!
built on 20081218-10:06 ).
boot:
Allocated 8 Megs of memory at 0x40000000 for kernel
Loaded kernel version 2.6.26
Loading initial ramdisk... (3 Replies)
Discussion started by: mtk
3 Replies
6. Solaris
Dear Guru,
My boss has a plan to upgrade cpu of server so he needs to know how much better performance(percentage) is Ultra SPARC IV+ 1.95 GHz than Ultra SPARC IV 1.35 GHz?.
I am looking for documentation to reference but I didn't see anything close to my point. If who know,... (3 Replies)
Discussion started by: unitipon
3 Replies
7. Solaris
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Discussion started by: jamie_collins
3 Replies
8. Ubuntu
I have a Sun Blade 1000 machine that I installed Ubuntu 7.10 SPARC onto. The only user configured (configure during install) cannot use sudo. When I try to issue a command using sudo (ex. sudo apt-get install) it asks me for my password and returns the error "user not found in sudoers file". I need... (4 Replies)
Discussion started by: swilso
4 Replies
9. Solaris
I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10.
I've got the Oracle installation guide for it and I got as far as:
"4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive."
I don't have a CD-ROM by that name and a web search for that... (21 Replies)
Discussion started by: Michele31416
21 Replies
10. Hardware
Hi all,
I managed to salvage form work an old Sun Sparc Ultra 30. I have had it stored (controlled storage) for a few years and decided to get it home and boot it up.
It starts up with a beep then I can hear disks spinning up, CDROM moving but nothing is displayed on the monitor.
Can... (2 Replies)
Discussion started by: robbo007
2 Replies
LEARN ABOUT SUNOS
if_mpadm
if_mpadm(1M) System Administration Commands if_mpadm(1M)
NAME
if_mpadm - change operational status of interfaces within a multipathing group
SYNOPSIS
/usr/sbin/if_mpadm -d interface_name
/usr/sbin/if_mpadm -r interface_name
DESCRIPTION
Use the if_mpadm utility to change the operational status of interfaces that are part of an IP multipathing group. If the interface is
operational, you can use if_mpadm -d to detach or off-line the interface. If the interface is off-lined, use if_mpadm -r to revert it to
its original state.
When a network interface is off-lined, all network access fails over to a different interface in the IP multipathing group. Any addresses
that do not failover are brought down. Network access includes unicast, broadcast, and multicast for IPv4 and unicast and multicast for
IPv6. Addresses marked with IFF_NOFAILOVER do not failover. They are marked down. After an interface is off-lined, the system will not use
the interface for any outbound or inbound traffic, and the interface can be safely removed from the system without any loss of network
access.
The if_mpadm utility can be applied only to interfaces that are part of an IP multipathing group.
OPTIONS
The if_mpadm utility supports the following options:
-d interface_name Detach or off-line the interface specified by interface_name.
-r interface_name Reattach or undo the previous detach or off-line operation on the interface specified by interface_name. Unless
the -d option was used to detach or off-line the interface, this option will fail.
EXAMPLES
Example 1: Detaching an Interface
Use the following command to off-line or detach the interface. All network access will failover from hme0 to other interfaces in the same
IP multipathing group. If no other interfaces are in the same group, the operation will fail.
example% if_mpadm -d hme0
Example 2: Reattaching an Off-line Interface
Use the following command to undo the previous operation. Network access will failback to hme0.
example% if_mpdadm -r hme0
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable |
+-----------------------------+-----------------------------+
SEE ALSO
ifconfig(1M), in.mpathd(1M), attributes(5)
DIAGNOSTICS
off-line failed as there is no other functional interface available in the multipathing group for failing over the network access.
This message means that other interfaces in the group are failed over already or the multipathing configuration was not suitable for com-
pleting a failover.
off-line cannot be undone because multipathing configuration is not consistent across all the interfaces in the group.
This message means that some interfaces in the IP multipathing group are not configured consistently with other interfaces in the group,
for example, one of the interfaces in the group does not have an IFF_NOFAILOVER address.
SunOS 5.10 3 Sep 2002 if_mpadm(1M)