12-16-2008
Breaking AIX cluster
Hello All,
I was just wondering:
How do I break a server cluster in an AIX 5.2 environment?
Thanks.
10 More Discussions You Might Find Interesting
1. HP-UX
Can some one point this UNIX newbie to a web site or directions on the steps needed to break a mirror in HP-UNIX to change a bad hard drive. (4 Replies)
Discussion started by: egress1
4 Replies
2. High Performance Computing
Provides a description of how to set up a Solaris Cluster Express cluster in a VirtualBox on OpenSolaris.
More... (0 Replies)
Discussion started by: Linux Bot
0 Replies
3. High Performance Computing
Dear All,
Can anyone explain about Pros and Cons of SUN and Veritas Cluster ?
Any comparison chart is highly appreciated.
Regards,
RAA (4 Replies)
Discussion started by: RAA
4 Replies
4. AIX
We run two p5 nodes running AIX 5L in a cluster mode (HACMP), both the nodes share external disk arrays. Only the primary node can access the shared disks at a given point of time.
We are in the process of adding two new disks to the disk arrays so as to make them available to the existing... (3 Replies)
Discussion started by: dnicky
3 Replies
5. AIX
Hello,
I was wondering if I have 3 nodes (A, B, C) all configured to startup with HACMP, but I would like to configure HACMP in such a way:
1) Node B should startup first. After the cluster successfully starts up and mounts all the filesystems, then
2) Node A, and Node C should startup !
... (4 Replies)
Discussion started by: filosophizer
4 Replies
6. AIX
I have a 2-node Power 7 - 16cpu - 32gb RAM - AIX 6L cluster. The production node has 10 physical cpus (40 cores) and 24gb of RAM.
The cluster has been live for 6 weeks and I'm seeing some things on the production node that I think could be of concern but wanted to get some opinions.
The... (6 Replies)
Discussion started by: troym72
6 Replies
7. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
8. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
9. AIX
As i have updated a lot of HACMP-nodes lately the question arises how to do it with minimal downtime. Of course it is easily possible to have a downtime and do the version update during this. In the best of worlds you always get the downtime you need - unfortunately we have yet to find this best of... (4 Replies)
Discussion started by: bakunin
4 Replies
10. AIX
Hello,
I am working on applications on an AIX 6.1 two-node cluster, with an active and passive node. Is there a command that will show me which mount points / file systems are shared and 'swing' from one node to the other when the active node changes, and which mount points are truly local to... (6 Replies)
Discussion started by: Clovis_Sangrail
6 Replies
cmruncl(1m) cmruncl(1m)
NAME
cmruncl - run a high availability cluster
SYNOPSIS
cmruncl [-f] [-v] [-n node_name...] [-t | -w none]
DESCRIPTION
cmruncl causes all nodes in a configured cluster or all nodes specified to start their cluster daemons and form a new cluster.
To start a cluster, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the cluster configuration
file. See access policy in cmquerycl(1m).
This command should only be run when the cluster is not active on any of the configured nodes. This command verifies the network configu-
ration before causing the nodes to start their cluster daemons. If a cluster is already running on a subset of the nodes, the cmrunnode
command should be used to start the remaining nodes and force them to join the existing cluster.
If node_name is not specified, the cluster daemons will be started on all the nodes in the cluster. All nodes in the cluster must be
available for the cluster to start unless a subset of nodes is specified.
Options
cmruncl supports the following options:
-f Force cluster startup without warning message and continuation prompt that are printed with the -n option.
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages.
The -w option is not required with the -t option as -t does not validate network connectivity, but assumes that all the
nodes can meet any external dependencies such as EMS resources, package subnets, and storage.
-n node_name...
Start the cluster daemon on the specified subset of node(s).
-w none By default network probing is performed to check that the network connectivity is the same as when the cluster was config-
ured. Any anomalies are reported before the cluster daemons are started. The -w none option disables this probing. The
option should only be used if this network configuration is known to be correct from a recent check.
RETURN VALUE
cmruncl returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Run the cluster daemon:
cmruncl
Run the cluster daemons on node1 and node2:
cmruncl -n node1 -n node2
AUTHOR
cmruncl was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmhaltnode(1m), cmrunnode(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmruncl(1m)