I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
OK, so I have a real dumb question, but I am desperate for an answer.
If my Sun machine shows the following out put.
root@xxxx:/# egrep network /etc/path_to_inst
"/pci@1f,0/pci@1,1/network@c,1" 0 "eri"
"/pci@1f,0/pci@1,1/network@5,1" 1 "eri"
Does that indicate that there is one eri... (2 Replies)
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT CENTOS
locale::codes::langext
Locale::Codes::LangExt(3) User Contributed Perl Documentation Locale::Codes::LangExt(3)NAME
Locale::Codes::LangExt - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangExt;
$lext = code2langext('acm'); # $lext gets 'Mesopotamian Arabic'
$code = langext2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langext_codes();
@names = all_langext_names();
DESCRIPTION
The "Locale::Codes::LangExt" module provides access to standard codes used for identifying language extensions, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language extensions. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langext('acm','alpha');
$lext = code2langext('acm',LOCALE_LANGEXT_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from the IANA language registry, such as 'acm' for Mesopotamian Arabic.
This is the default code set.
ROUTINES
code2langext ( CODE [,CODESET] )
langext2code ( NAME [,CODESET] )
langext_code2code ( CODE ,CODESET ,CODESET2 )
all_langext_codes ( [CODESET] )
all_langext_names ( [CODESET] )
Locale::Codes::LangExt::rename_langext ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangExt::add_langext ( CODE ,NAME [,CODESET] )
Locale::Codes::LangExt::delete_langext ( CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_alias ( NAME ,NEW_NAME )
Locale::Codes::LangExt::delete_langext_alias ( NAME )
Locale::Codes::LangExt::rename_langext_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::delete_langext_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.16.3 2013-02-27 Locale::Codes::LangExt(3)