I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
OK, so I have a real dumb question, but I am desperate for an answer.
If my Sun machine shows the following out put.
root@xxxx:/# egrep network /etc/path_to_inst
"/pci@1f,0/pci@1,1/network@c,1" 0 "eri"
"/pci@1f,0/pci@1,1/network@5,1" 1 "eri"
Does that indicate that there is one eri... (2 Replies)
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT MOJAVE
locale::codes::langfam5.18
Locale::Codes::LangFam(3pm) Perl Programmers Reference Guide Locale::Codes::LangFam(3pm)NAME
Locale::Codes::LangFam - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangFam;
$lext = code2langfam('apa'); # $lext gets 'Apache languages'
$code = langfam2code('Apache languages'); # $code gets 'apa'
@codes = all_langfam_codes();
@names = all_langfam_names();
DESCRIPTION
The "Locale::Codes::LangFam" module provides access to standard codes used for identifying language families, such as those as defined in
ISO 639-5.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default ISO 639-5
language family codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language families. A code set may be specified using either a name, or a
constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langfam('apa','alpha');
$lext = code2langfam('apa',LOCALE_LANGFAM_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from ISO 639-5 such as 'apa' for Apache languages.
This is the default code set.
ROUTINES
code2langfam ( CODE [,CODESET] )
langfam2code ( NAME [,CODESET] )
langfam_code2code ( CODE ,CODESET ,CODESET2 )
all_langfam_codes ( [CODESET] )
all_langfam_names ( [CODESET] )
Locale::Codes::LangFam::rename_langfam ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangFam::add_langfam ( CODE ,NAME [,CODESET] )
Locale::Codes::LangFam::delete_langfam ( CODE [,CODESET] )
Locale::Codes::LangFam::add_langfam_alias ( NAME ,NEW_NAME )
Locale::Codes::LangFam::delete_langfam_alias ( NAME )
Locale::Codes::LangFam::rename_langfam_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangFam::add_langfam_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangFam::delete_langfam_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.loc.gov/standards/iso639-5/id.php
ISO 639-5 .
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2013-11-04 Locale::Codes::LangFam(3pm)