|
|
Sponsored Content
Operating Systems
Solaris
How to identifying the network card ?
Post 302268296 by incredible on Monday 15th of December 2008 10:32:04 AM
12-15-2008
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
5. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
6. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
9. Hardware
OK, so I have a real dumb question, but I am desperate for an answer.
If my Sun machine shows the following out put.
root@xxxx:/# egrep network /etc/path_to_inst
"/pci@1f,0/pci@1,1/network@c,1" 0 "eri"
"/pci@1f,0/pci@1,1/network@5,1" 1 "eri"
Does that indicate that there is one eri... (2 Replies)
Discussion started by: Tirmazi
2 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT SUSE
vpcd
vpcd(8) powerman vpcd(8) NAME
vpcd - virtual power control daemon SYNOPSIS
vpcd [--port PORT] DESCRIPTION
vpcd is a test program for PowerMan which emulates a remote power control device. It can be run interactively by the powerman daemon, or it can listen on a port of your choosing. OPTIONS
-p, --port PORT Instructs vpcd to listen for connections on the specified port instead of using stdin/stdout. Only one connection will be accepted. INTERACTIVE COMMANDS
The following commands are available at the vpcd> prompt: login The login command must br run before any of the other commands will work. No username or password is required. logoff Return vpcd to the initial state. stat PLUG|* Show the power status of PLUG. If PLUG is ``*'', perform this action on all plugs. beacon PLUG|* Show the beacon status of PLUG. If PLUG is ``*'', perform this action on all plugs. temp PLUG|* Show the temperature of the node attached to PLUG. If PLUG is ``*'', perform this action on all plugs. spew COUNT Print COUNT 80-char lines. This is the basis of a buffer handling test. on PLUG|* Turn on PLUG. If PLUG is ``*'', perform this action on all plugs. off PLUG|* Turn off PLUG. If PLUG is ``*'', perform this action on all plugs. flash PLUG|* Light the beacon on PLUG. If PLUG is ``*'', perform this action on all plugs. unflash PLUG|* Unlight the beacon on PLUG. If PLUG is ``*'', perform this action on all plugs. reset PLUG|* Reset the node attached to PLUG. If PLUG is ``*'', perform this action on all plugs. FILES
/usr/sbin/vpcd ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms of the GNU GPL. SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7). http://sourceforge.net/projects/powerman powerman-2.3.5 2009-02-09 vpcd(8)