Sponsored Content
Special Forums IP Networking redirect routing on non-default interface Post 302268236 by otheus on Monday 15th of December 2008 08:37:44 AM
Old 12-15-2008
Nothing is obvious to me. What do tables T3 and ADSL look like?
 

7 More Discussions You Might Find Interesting

1. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

2. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

3. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

4. Solaris

Traffic routing through wrong interface

Solaris-9 server is having one primary IP 10.41.161.14 on qfe0 and 10.41.116.0 on qfe3:1. Traffic is going through virtual interface instead of physical interface. How should I force traffic to go with primary interface. root@smtsrvn01:/# netstat -nr Routing Table: IPv4 Destination ... (2 Replies)
Discussion started by: solaris_1977
2 Replies

5. IP Networking

Linux load balancer ping redirect to other interface

Im configuring centos with load balance with ip route and ip rule Eth0 192.168.1.5 Eth1 192.168.5.128 # ip route 192.168.5.0/24 dev eth1 scope link src 192.168.5.128 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.5 169.254.0.0/16 dev eth1 scope link # ip route show... (2 Replies)
Discussion started by: hadinetcat
2 Replies

6. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

7. IP Networking

Port based multi interface routing

Hello, I wanted to setup routing certain traffic (http/s) out via a second (faster) interface, like described in the following docs (may not post urls): linux-ip.net /html/adv-multi-internet.html thegeekstuff.com /2014/08/add-route-ip-command/ I already had this working years ago on... (0 Replies)
Discussion started by: hyphan
0 Replies
ipkungfu(8)						      System Manager's Manual						       ipkungfu(8)

NAME
ipkungfu - An iptables-based firewall for Linux SYNOPSIS
ipkungfu [ -c ] [ -t ] [ -d ] [ -h ] [ -v ] [ --quiet ] [ --panic ] [ --no-caching DESCRIPTION
ipkungfu is an iptables-based Linux firewall. The primary design goals are security, ease of use, and performance, in that order. It takes advantage of advanced features of iptables, tcpwrappers, and the Linux kernel. It also simplifies the configuration of internet connection sharing, advanced routing, and other networking needs. OPTIONS
-c (or --check) Check whether ipkungfu is loaded, and report any command line options it may have been loaded with. -t (or --test) Runs a configuration test, and displays the results. Note that this does not test or display all configuration options. This gives you an opportunity to verify that major configuration options are correct before putting them into action. -d (or --disable) Disables the firewall. It is important to know exactly what this option does. All traffic is allowed in and out, and in the case of a gateway, all NATed traffic is forwarded (the option retains your connection sharing options). Custom rules are not implemented, and deny_hosts.conf is ignored. -f (or --flush) Disables the firewall COMPLETELY. All rules are flushed, all chains are removed. Any port forwarding or internet connection sharing will cease to work. -h (or --help) Displays brief usage information and exits. -v (or --version) Displays version information and exits. --quiet Runs ipkungfu with no standard output --panic Drops ALL traffic in all directions on all network interfaces. You should probably never use this option. The --panic option is available for the highly unusual situation where you know that an attack is underway but you know of no other way to stop it. --failsafe If ipkungfu fails, --failsafe will cause all firewall policies to revert to ACCEPT. This is useful when working with ipkungfu remotely, to prevent loss of remote access due to firewall failure. --no-caching Disables rules caching feature. FILES
/etc/ipkungfu/ipkungfu.conf /etc/ipkungfu/advanced.conf /etc/ipkungfu/accept_hosts.conf /etc/ipkungfu/deny_hosts.conf /etc/ipkungfu/custom.conf /etc/ipkungfu/log.conf /etc/ipkungfu/redirect.conf /etc/ipkungfu/services.conf /usr/sbin/ipkungfu /usr/share/doc/ipkungfu/AUTHORS /usr/share/doc/ipkungfu/README /usr/share/doc/ipkungfu/FAQ /usr/share/doc/ipkungfu/ChangeLog /usr/share/doc/ipkungfu/COPYING SEE ALSO
iptables(8). January 2003 ipkungfu(8)
All times are GMT -4. The time now is 11:18 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy