12-15-2008
ifconfig -a
Before anyone touches a UNIX based system are 10 commands they should know, this is one of them.
ms. stevi
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
5. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
6. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
9. Hardware
OK, so I have a real dumb question, but I am desperate for an answer.
If my Sun machine shows the following out put.
root@xxxx:/# egrep network /etc/path_to_inst
"/pci@1f,0/pci@1,1/network@c,1" 0 "eri"
"/pci@1f,0/pci@1,1/network@5,1" 1 "eri"
Does that indicate that there is one eri... (2 Replies)
Discussion started by: Tirmazi
2 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT MINIX
inet_type
inet_type(4) File Formats inet_type(4)
NAME
inet_type - default Internet protocol type
SYNOPSIS
/etc/default/inet_type
DESCRIPTION
The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.
The inet_type file can contain a number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.
The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file. By default,
both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
setting the value of DEFAULT_IP. The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
will be displayed:
IP_VERSION4 Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
and netstat(1M) commands.
IP_VERSION6 Displays both IPv4 and IPv6 related information for ifconfig and netstat.
BOTH Displays both IPv4 and IPv6 related information for ifconfig and netstat.
The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For example,
even if the value of DEFAULT_IP is IP_VERSION4, the command
example% ifconfig -a6
will display all IPv6 interfaces.
EXAMPLES
Example 1: Suppressing IPv6 Related Output
This is what the inet_type file must contain if you want to suppress IPv6 related output:
DEFAULT_IP=IP_VERSION4
SEE ALSO
ifconfig(1M), netstat(1M)
SunOS 5.10 16 Jun 1999 inet_type(4)