12-15-2008
ifconfig -a
Before anyone touches a UNIX based system are 10 commands they should know, this is one of them.
ms. stevi
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
5. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
6. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
9. Hardware
OK, so I have a real dumb question, but I am desperate for an answer.
If my Sun machine shows the following out put.
root@xxxx:/# egrep network /etc/path_to_inst
"/pci@1f,0/pci@1,1/network@c,1" 0 "eri"
"/pci@1f,0/pci@1,1/network@5,1" 1 "eri"
Does that indicate that there is one eri... (2 Replies)
Discussion started by: Tirmazi
2 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT OPENSOLARIS
ifparse
ifparse(1M) System Administration Commands ifparse(1M)
NAME
ifparse - parse ifconfig command line
SYNOPSIS
/sbin/ifparse [-fs] addr_family commands
DESCRIPTION
Use the ifparse command to parse the ifconfig(1M) command line options and output substrings, one per line, as appropriate. If no options
are specified, ifparse returns the entire ifconfig command line as a series of substrings, one per line.
OPTIONS
The ifparse command supports the following options:
-f Lists only substrings of the ifconfig command line that are relevant to IP network multipath failover
-s Lists only substrings of the ifconfig command line that are not relevant to IP network multipath failover
OPERANDS
The ifparse command does not support the interface operand of the ifconfig command.
EXAMPLES
Example 1 Parsing Command Line Options Relevant to Failover
The following example shows the use of the ifparse command to parse the command line options relevant to IP network multipath failover:
example# ifparse -f inet 1.2.3.4 up group one addif 1.2.3.5 -failover up
set 1.2.3.4 up
Example 2 Parsing Command Line Options That Are Not Relevant to Failover
The following example shows the use of the ifparse command to parse the command line options that are not relevant to IP network multipath
failover:
example# ifparse -s inet 1.2.3.4 up group one addif 1.2.3.5 -failover up
group one
addif 1.2.3.5 -failover up
Example 3 Parsing the Command Line For All Options
The following example shows the use of the ifparse command to parse the command line for all ifconfig options:
example# ifparse inet 1.2.3.4 up group one addif 1.2.3.5 -failover up
group one
set 1.2.3.4 up
addif 1.2.3.5 -failover up
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsr |
+-----------------------------+-----------------------------+
|Stability Level |Obsolete |
+-----------------------------+-----------------------------+
SEE ALSO
ifconfig(1M), attributes(5)
DIAGNOSTICS
usage: -fs <addr_family> <commands>
Description:
This message indicates an invalid command line.
ifparse: Not enough space
Description:
This message indicates insufficient memory.
ifparse: dhcp not supported for inet6
Description:
DHCP operations are not supported for the inet6 address family.
ifparse: Operation <operation> not supported for <addr_family>
Description:
Most operations cannot be used with all address families. For example, the broadcast operation is not supported on the inet6 address
family.
ifparse: no argument for <operation>
Description:
Some operations, for example broadcast, require an argument.
NOTES
The ifparse command is classified as an obsolete interface. It will likely be removed in a future release. You should not develop applica-
tions that depend upon this interface.
SunOS 5.11 9 May 2001 ifparse(1M)