Sponsored Content
Operating Systems Solaris How to identifying the network card ? Post 302268109 by kumarmani on Monday 15th of December 2008 04:12:14 AM
Old 12-15-2008
How to identifying the network card ?

Hi Experts,

Can we use some command from unix to find the available network interface? I did tried

Quote:
# prtdiag |grep network
Its listing following, however how can I decide the which vender card is attached

Quote:
pci 66 MB pci108e,1648 (network)
okay /pci@1f,700000/network@2
pci 66 MB pci108e,1648 (network)
okay /pci@1f,700000/network@2,1
pci 66 MB pci108e,1648 (network)
okay /pci@1d,700000/network@2
pci 66 MB pci108e,1648 (network)
okay /pci@1d,700000/network@2,1
e.g. if its hme , bge or some thing else

Thanks
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies

3. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

4. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

5. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

6. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies

7. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

8. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies

9. Hardware

Identifying Network Ports

OK, so I have a real dumb question, but I am desperate for an answer. If my Sun machine shows the following out put. root@xxxx:/# egrep network /etc/path_to_inst "/pci@1f,0/pci@1,1/network@c,1" 0 "eri" "/pci@1f,0/pci@1,1/network@5,1" 1 "eri" Does that indicate that there is one eri... (2 Replies)
Discussion started by: Tirmazi
2 Replies

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
MALO(4) 						   BSD Kernel Interfaces Manual 						   MALO(4)

NAME
malo -- Marvell Libertas IEEE 802.11b/g wireless network driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device malo device pci device wlan device firmware Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5): if_malo_load="YES" DESCRIPTION
The malo driver provides support for Marvell Libertas 88W8335 based PCI and Cardbus network adapters. malo supports station and monitor mode operation. Only one virtual interface may be configured at any time. For more information on configuring this device, see ifconfig(8). This driver requires the malofw firmware kernel module be installed before it will work. The firmware files are not publicly available. A port of the firmware can be found at: http://weongyo.org/project/malo/malo-firmware-1.4.tar.gz The firmware kernel module can be installed by extracting the archive and running 'make install clean' in the malo-firmware-1.4 directory. HARDWARE
The following cards are among those supported by the malo driver: Card Chip Bus Standard Netgear WG311v3 88W8335 PCI b/g Tenda TWL542P 88W8335 PCI b/g U-Khan UW-2054i 88W8335 PCI b/g EXAMPLES
Join an existing BSS network (i.e., connect to an access point): ifconfig wlan create wlandev malo0 inet 192.168.0.20 netmask 0xffffff00 Join a specific BSS network with network name ``my_net'': ifconfig wlan create wlandev malo0 ssid my_net up Join a specific BSS network with 64-bit WEP encryption: ifconfig wlan create wlandev malo0 ssid my_net wepmode on wepkey 0x1234567890 weptxkey 1 up SEE ALSO
cardbus(4), pci(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8) HISTORY
The malo device driver first appeared in FreeBSD 7.1. BSD
October 21, 2009 BSD
All times are GMT -4. The time now is 04:48 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy