12-15-2008
How to identifying the network card ?
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
Quote:
pci 66 MB pci108e,1648 (network)
okay /pci@1f,700000/network@2
pci 66 MB pci108e,1648 (network)
okay /pci@1f,700000/network@2,1
pci 66 MB pci108e,1648 (network)
okay /pci@1d,700000/network@2
pci 66 MB pci108e,1648 (network)
okay /pci@1d,700000/network@2,1
e.g. if its hme , bge or some thing else
Thanks
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
5. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
6. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
9. Hardware
OK, so I have a real dumb question, but I am desperate for an answer.
If my Sun machine shows the following out put.
root@xxxx:/# egrep network /etc/path_to_inst
"/pci@1f,0/pci@1,1/network@c,1" 0 "eri"
"/pci@1f,0/pci@1,1/network@5,1" 1 "eri"
Does that indicate that there is one eri... (2 Replies)
Discussion started by: Tirmazi
2 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT FREEBSD
hv_netvsc
HYPER-V(4) BSD Kernel Interfaces Manual HYPER-V(4)
NAME
hv_netvsc -- Hyper-V Network Virtual Service Consumer
SYNOPSIS
To compile this driver into the kernel, place the following lines in the system kernel configuration file:
device hyperv
DESCRIPTION
The hv_netvsc driver implements the virtual network device for FreeBSD guest partitions running on Hyper-V. FreeBSD guest partitions running
on Hyper-V do not have direct access to network devices attached to the Hyper-V server. Although a FreeBSD guest can access network devices
using Hyper-V's full emulation mode, the performance in this mode tends to be unsatisfactory.
To counter the above issues, the hv_netvsc driver implements a network Virtual Service Consumer (VSC) that relays network requests from the
guest partition to the network Virtual Service Provider (VSP) hosted in the root partition using the high performance data exchange infra-
structure provided by hv_vmbus(4) driver. The VSP in the root partition then forwards the network related requests to the physical network
card.
SEE ALSO
hv_ata_pci_disengage(4), hv_storvsc(4), hv_utils(4), hv_vmbus(4)
HISTORY
Support for hv_netvsc first appeared in FreeBSD 10.0. The driver was developed through a joint effort between Citrix Incorporated, Microsoft
Corporation, and Network Appliance Incorporated.
AUTHORS
FreeBSD support for hv_netvsc was first added by Microsoft BSD Integration Services Team <bsdic@microsoft.com>.
BSD
September 10, 2013 BSD