12-06-2008
If your network has a DHCP server, Then the easiest way to connect to the internet , is to have a dynamic adress. The file used to connect to the internet is /etc/resolv.conf which is automatically updated when the network service starts.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi. I have installed Solaris 8 and I am trying to configure the network settings. For some reason every time I reboot, my card loses its configuration. I can run ifconfig and the only IP address bound to my card (on either interface) is 127.0.0.1. I can change that to a valid IP address on my... (8 Replies)
Discussion started by: Ask Me
8 Replies
2. IP Networking
Hi,
I need to configure the Network for a Sun Solaris systems.
The OS info is SunOS Sparsh 5.8 Generic_108528-13 Sun4u Sparc SUNW,Ultra-250.
Please do let me know, how shall I shart with & more in configuring the Network.
Below is the list of Network Configuration I need to Make
... (2 Replies)
Discussion started by: S.Vishwanath
2 Replies
3. HP-UX
Hi,
I have installed a HP-UX B.11.00 U 9000/800 Server in one of the domain. And I'm also able to telnet/ping into this server from systems in the same domain.
But I'm not able to telnet/ping into this server from a different domain.
So, what shoud need to do to achieve this... (6 Replies)
Discussion started by: S.Vishwanath
6 Replies
4. Solaris
hi again...
i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0.
there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies
5. Solaris
Can someone please point me in the correct direction of where I configure the network information on SunOS 5.8 server? (Searching SunSolve and Google have resulted in thousands of fixes for potential errors, but I can't find the general instructions, etc. for starting the process).
Thanks! (2 Replies)
Discussion started by: FredSmith
2 Replies
6. UNIX for Dummies Questions & Answers
I need to know what commands I will need to use to change a host name, IP Address, and network configurations (routerings, dns, etc) and a Unix SCO machine.
Also, if there is any short tutorials on using the commands, i would defiently like that information.
Thanks!!! (1 Reply)
Discussion started by: HandleX
1 Replies
7. SCO
I have a SCO 5.07 Server and I am trying to get it on my network. I have edited the /etc/hosts file and /etc/rc2.d/s99route . I has connectivity on the NIC card but not sure if I am forgetting another file. Thanks! (2 Replies)
Discussion started by: andrewd
2 Replies
8. UNIX for Dummies Questions & Answers
I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the
ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and
Route add default 192.168.1.xxx command to gain back my internet.
I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies
9. Solaris
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies
10. UNIX for Advanced & Expert Users
Hi all,
I got following configuration problem
I need to configure tiny network on openbsd
I got server1 with 3 interfaces vic0 em0 em1
The interface vic0 on server1 has follwoing IP 172.16.1.1
em0
firstly I would like to configure network under em0 (I have assigned to em0 following... (1 Reply)
Discussion started by: kvok
1 Replies
LEARN ABOUT PHP
socket-context-options
SOCKET-CONTEXT-OPTIONS(3) 1 SOCKET-CONTEXT-OPTIONS(3)
Socket context options - Socket context option listing
Socket context options are available for all wrappers that work over sockets, like tcp, http and ftp.
o $bindto
- Used to specify the IP address (either IPv4 or IPv6) and/or the port number that PHP will use to access the network. The syntax
is ip:port for IPv4 addresses, and [ip]:port for IPv6 addresses. Setting the IP or the port to 0 will let the system choose the IP
and/or port.
Note
As FTP creates two socket connections during normal operation, the port number cannot be specified using this option.
o $backlog
- Used to limit the number of outstanding connections in the socket's listen queue.
Note
This is only applicable to stream_socket_server(3).
+--------+-----------------+
|Version | |
| | |
| | Description |
| | |
+--------+-----------------+
| 5.3.3 | |
| | |
| | Added backlog. |
| | |
| 5.1.0 | |
| | |
| | Added bindto. |
| | |
+--------+-----------------+
Example #1
Basic $bindto usage example
<?php
// connect to the internet using the '192.168.0.100' IP
$opts = array(
'socket' => array(
'bindto' => '192.168.0.100:0',
),
);
// connect to the internet using the '192.168.0.100' IP and port '7000'
$opts = array(
'socket' => array(
'bindto' => '192.168.0.100:7000',
),
);
// connect to the internet using the '2001:db8::1' IPv6 address
// and port '7000'
$opts = array(
'socket' => array(
'bindto' => '[2001:db8::1]:7000',
),
);
// connect to the internet using port '7000'
$opts = array(
'socket' => array(
'bindto' => '0:7000',
),
);
// create the context...
$context = stream_context_create($opts);
// ...and use it to fetch the data
echo file_get_contents('http://www.example.com', false, $context);
?>
PHP Documentation Group SOCKET-CONTEXT-OPTIONS(3)