Sponsored Content
Operating Systems Solaris Problem with Upgrading firmware on X4500 Post 302264747 by DukeNuke2 on Thursday 4th of December 2008 04:22:00 PM
Old 12-04-2008
you've already opend a thread for this:
Error updating Firmware in X4500

new thread closed.
 

10 More Discussions You Might Find Interesting

1. Solaris

How do i update firmware on X4500??

I have solaris X4500 with ILOM version 1.1.1. I want to update the firmware. I know that we need to use load -source tftp://tftpserver/image file But I do not understand what is the IP address of the tftp server that we need to type in there. Kindly, help me with this. Thank you (5 Replies)
Discussion started by: bharu_sri
5 Replies

2. Solaris

Error while upgrading firmware on X4500.

I get an error message when I try to upgrade the firmware. The error message is displayed below. Image has no uboot. DO NOT RESET OR YOU WILL BRICK THE ILOM. Please retry with the correct image I do not understand anything about this message. May I know what does it mean ? How can I get rid... (6 Replies)
Discussion started by: bharu_sri
6 Replies

3. Solaris

Error updating Firmware in X4500

I have X4500 machine with solaris 10 OS and software version 5.10. The firmware version is 1.1.1 and I am planning to upgrade the firmware. C H A P T E R 1 - Flash Upgrading Your Server to Software Release 1.2 I referred to the above link to do so. But, I do not understand what is the... (6 Replies)
Discussion started by: bharu_sri
6 Replies

4. Solaris

start /SP/console hangs in X4500

when I type start /SP/console... the console shows up but i cannot type anything over there. I do not understand what might be the reason for that. -> start /SP/console Are you sure you want to start /SP/console (y/n)? y Serial console started. To stop, type ESC ( I pressed enter many... (8 Replies)
Discussion started by: bharu_sri
8 Replies

5. Solaris

Partitioning X4500 running Solaris 10 OS

Hi guys I have a Sun Fire X4500 running Solaris 10 OS. It has 48 TB Hard Disk. I need to format it and make 3 partitions. Could someone give me a link or help me with this. Thank you (1 Reply)
Discussion started by: bharu_sri
1 Replies

6. Shell Programming and Scripting

Problem Executing Firmware Command using Shell Script

Guys, I have a script that should change one of the configuration Parameter in a http accelerator, this config change which will halt http traffic into device. So I have designed a script which should do these changes. But after executing this script, found that one of the input variable is not... (8 Replies)
Discussion started by: raghunsi
8 Replies

7. Solaris

Facing problem after upgrading the kernal patch level to 142900-12

I have a Solaris 10 OS having kernal patch level 138888-03 on several servers but recenlty I upgraded it into 142900-12 on some T-Series servers & v890 server after install them my syslog is increasing at a rate of 1GB on average on all servers . I believe its a bug, can somebody help me in... (1 Reply)
Discussion started by: sb200
1 Replies

8. Ubuntu

Encountering problem on upgrading the packages

Hi folks, Ubuntu 9.04 I have an old box not running for years. I just dig it out from the store room. On running; $ sudo aptitude update ...... ...... Err http://hk.archive.ubuntu.com jaunty/main Packages 404 Not Found Err http://hk.archive.ubuntu.com jaunty/restricted Packages ... (1 Reply)
Discussion started by: satimis
1 Replies

9. AIX

Problem after updating the firmware!

Hello AIX experts, I have 7038-6M2 server, its operating system is AIX 5.2, and its firmware is 3K041021 After some searching on net, I tried to update its firmware level to 3K080425, so I downloaded the required rpm, and followed the steps. After rebooting the server, it stopped and an error... (6 Replies)
Discussion started by: Mohannad
6 Replies

10. AIX

Problem Upgrading OS

Hi I've just upgraded OS - using "Migration with nimadm". The Nim master is a Power 6 server, and the source is 6100-09-04-1441. The migration was successful with a Power 6 - Nim client, but there was a problem with Power 5 - Nim client : the OS remained 6100-00-09-0920 icapp1:/]oslevel -s... (1 Reply)
Discussion started by: bobochacha29
1 Replies
URI::URL(3)						User Contributed Perl Documentation					       URI::URL(3)

NAME
URI::URL - Uniform Resource Locators SYNOPSIS
$u1 = URI::URL->new($str, $base); $u2 = $u1->abs; DESCRIPTION
This module is provided for backwards compatibility with modules that depend on the interface provided by the "URI::URL" class that used to be distributed with the libwww-perl library. The following differences exist compared to the "URI" class interface: o The URI::URL module exports the url() function as an alternate constructor interface. o The constructor takes an optional $base argument. The "URI::URL" class is a subclass of "URI::WithBase". o The URI::URL->newlocal class method is the same as URI::file->new_abs. o URI::URL::strict(1) o $url->print_on method o $url->crack method o $url->full_path: same as ($uri->abs_path || "/") o $url->netloc: same as $uri->authority o $url->epath, $url->equery: same as $uri->path, $uri->query o $url->path and $url->query pass unescaped strings. o $url->path_components: same as $uri->path_segments (if you don't consider path segment parameters) o $url->params and $url->eparams methods o $url->base method. See URI::WithBase. o $url->abs and $url->rel have an optional $base argument. See URI::WithBase. o $url->frag: same as $uri->fragment o $url->keywords: same as $uri->query_keywords o $url->localpath and friends map to $uri->file. o $url->address and $url->encoded822addr: same as $uri->to for mailto URI o $url->groupart method for news URI o $url->article: same as $uri->message SEE ALSO
URI, URI::WithBase COPYRIGHT
Copyright 1998-2000 Gisle Aas. perl v5.18.2 2012-02-11 URI::URL(3)
All times are GMT -4. The time now is 01:18 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy