12-04-2008
Your auto-neg cap is set to false? Check with your network guys the settings on the switch end.
snoop -d /dev/e1000g0
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I am setting up a test server for actual 2 node servers which will be behind load balancer. I will not be using sun cluster at all. The test machine is installed with solaris 10.
I am not sure how to setup a test env of 2 nodes on only 1 node..may be creating 2 zones on test server will... (8 Replies)
Discussion started by: upengan78
8 Replies
2. Solaris
Hi All,
Kindly help me in configuring IPMP or guid me to some link, tried goggling however no luck.
Thanks in anticipation (1 Reply)
Discussion started by: kumarmani
1 Replies
3. Solaris
Probe-based IPMP active - active
Probe-based IPMP active - passive
Link-based only active -standby
????
What are differences between
Probe-based IPMP active - passive anddd
Link-based only active -standby
???!!!
For example in active active probe-based IPMP there are
lets... (6 Replies)
Discussion started by: samar
6 Replies
4. Shell Programming and Scripting
Hi,
I want to use a config file as the base file and parse over the values of country and city parameters in the config file and generate separate config files as explained below.
I will be using the config file as mentioned below:
(config.txt)
country:a,b
city:1,2
type:b1... (1 Reply)
Discussion started by: clazzic
1 Replies
5. Solaris
Please tell me how to configure IPMP in vmware
what is the basic working concept of IPMP.
please help me (1 Reply)
Discussion started by: sijocg
1 Replies
6. Solaris
Hi all
i had two interface
ce0 and ce5
but when i run the ifconfig, it show me alot of extra virtual interface, may i know how to remove it?
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0:... (2 Replies)
Discussion started by: SmartAntz
2 Replies
7. Shell Programming and Scripting
Hi I am new to shell scripting. There is a requirement to write a shell script to meet follwing needs.Prompt reply shall be highly appreciated.
script that will compare two config files and produce 2 outputs - actual config file and a report indicating changes made.
OS :Susi linux ver 10.3.
... (4 Replies)
Discussion started by: muraliinfy04
4 Replies
8. Solaris
Can any one please explain me the concept behind IPMP in solaris clustering.Basic explanation would be really appreciated...
Thanks in Advance
vks (2 Replies)
Discussion started by: vks47
2 Replies
9. Solaris
Dear All,
After configuring IPMP in 2 fresh Servers (T5520 and T2000) I can't login in any of them using SSH, I can login by serial console then I had to enable Telnet to access.
IPMP works fine.
This is the error in /var/adm/messages:
sshd: Failed password for lvalle from 172.28.12.95 port... (0 Replies)
Discussion started by: Luis Valle
0 Replies
10. Red Hat
Hi folks,
I am trying to configure Apache webserver and also a virtual host inside this webserver.
For Global server config: /var/www/html/index.html
For virtual host config: /var/www/virtual/index.html
Both client10 & www10 are pointing to 192.168.122.10 IP address.
BUT, MY... (1 Reply)
Discussion started by: freebird8z
1 Replies
LEARN ABOUT LINUX
ttysnoop
TTYSNOOP(8) BSD System Manager's Manual TTYSNOOP(8)
NAME
ttysnoop -- snoop on a user's tty
SYNOPSIS
ttysnoop [pty]
ttysnoops
DESCRIPTION
The ttysnoop / ttysnoops client-server combo can be used to snoop (watch) on a user's login tty. The server (ttysnoops) is usually started
by getty(8) or telnetd(8) and reads the file /etc/snooptab to find out which tty's should be cloned and which programs to run on them (usu-
ally /bin/login). A tty may be snooped through a pre-determined (ie. fixed) device, or through a dynamically allocated pseudo-tty (pty).
This is also specified in the /etc/snooptab file. To connect to the pty, the client ttysnoop should be used. The available pseudo terminals
pty are present as sockets in the directory /var/spool/ttysnoop/.
Format of /etc/snooptab
The /etc/snooptab file may contain comment lines (starting with a '#'), empty lines, or entries for tty's that should be snooped upon. The
format of such an entry is as follows:
tty snoop-device type program
where tty is the leaf-name of the tty that should be snooped upon (eg. ttyS2, not /dev/ttyS2) OR the wildcard '*', which matches ANY tty.
snoop-device is the device through which tty should be snooped (eg. /dev/tty8) OR the literal constant "socket". The latter is used to tell
ttysnoops that the snoop-device will be a dynamically allocated pty. type specifies the type of program that should be run, currently recog-
nized types are "init", "user" and "login" although the former two aren't really needed. Finally, program is the full pathname to the program
to run when ttysnoops has cloned tty onto snoop-device.
EXAMPLE
The following example /etc/snooptab file should illustrate the typical use of ttysnoop / ttysnoops:
#
# example /etc/snooptab
#
ttyS0 /dev/tty7 login /bin/login
ttyS1 /dev/tty8 login /bin/login
#
# the wildcard tty should always be the last one in the file
#
* socket login /bin/login
#
# example end
#
With the above example, whenever a user logs in on /dev/ttyS0 or /dev/ttyS1, either tty will be snooped through /dev/tty7 or /dev/tty8
respectively. Any other tty's will be snooped through a pty that will be allocated at the time of login. The system-administrator can then
run ttysnoop pty to snoop through the pty. Note that it is up to the system-administrator to setup getty and/or telnetd so that they execute
ttysnoops instead of /bin/login.
SEE ALSO
getty(8), telnetd(8)
FILES
/etc/snooptab
BUGS
The program is unable to do any terminal control-code translations for the original tty and the snoop-device. I doubt it will ever do this.
AUTHOR
Carl Declerck, carl@miskatonic.inbe.net
BSD August 8 1994 BSD