12-02-2008
HACMP LV size is not reflecting
Hi
i increased the lv size using smit hacmp.
but, the new size is not reflecting.. why?.
the pp size is 512 MB. before it was 4 PP's. i increased to 10 PP's.
when i type df -m /xxx.. it is showing 2GB only.
see the info below..
root@db:/ > df -m /xxx/xxx
Filesystem MB blocks Free %Used Iused %Iused Mounted on
/dev/xxxx 2048.00 271.36 87% 13 1% /app/d2
root@db:/ > lslv xxxx
LOGICAL VOLUME: xxxxx VOLUME GROUP: ora_vg
LV IDENTIFIER: 002a127f00004c00000001028918726f.35 PERMISSION: read/write
VG STATE: active/complete LV STATE: opened/syncd
TYPE: jfs2 WRITE VERIFY: off
MAX LPs: 512 PP SIZE: 512 megabyte(s)
COPIES: 1 SCHED POLICY: parallel
LPs: 10 PPs: 10
STALE PPs: 0 BB POLICY: relocatable
INTER-POLICY: minimum RELOCATABLE: yes
INTRA-POLICY: middle UPPER BOUND: 32
MOUNT POINT: /xxx/xxx LABEL: /xxx/xxx
MIRROR WRITE CONSISTENCY: on/ACTIVE
EACH LP COPY ON A SEPARATE PV ?: yes
Serialize IO ?: NO
can someone help me on this..
thanks
10 More Discussions You Might Find Interesting
1. Solaris
hi all,
in my server there are some specific application files which are spread through out the server... these are spread in folders..sub-folders..chid folders...
please help me, how can i find the total size of these specific files in the server... (3 Replies)
Discussion started by: abhinov
3 Replies
2. Solaris
Hi all,
I am trying to modify the file fs-root (on belenix).
Here is the problem..
I just wanted to check whether any modifications done to the file will be reflected when its booted up, so just echoed a statement and saved it back to the cd and then booted it..
Unfortunately it did not... (0 Replies)
Discussion started by: wrapster
0 Replies
3. Solaris
HI ,
I could see in df -k output that a mount point is 100% full.
But i could not find any files with huge size that can be removed.
So, i have umounted and mounted the filesystem again.
Now, in my df -k output i could see that th eutilization is only 7%.
Can anyone please suggest what... (3 Replies)
Discussion started by: sag71155
3 Replies
4. Programming
I make some changes in a JSP file but the changes do not reflect on tomcat server. In my server.xml 'reloadable' paramtere is set to true. I even treid restarting the server. The changes still not reflect.
The changes do reflect in a day or two. am not sure why this is happening. Shall... (3 Replies)
Discussion started by: Shikha Agrawal
3 Replies
5. AIX
How to increase the filesystem size in HACMP.
what is the difference between normal chfs command and increase the filesystem size in HACMP. (4 Replies)
Discussion started by: AIXlearner
4 Replies
6. Shell Programming and Scripting
#!/bin/sh
##########################################################################################################
#This script is being used for AOK application for cleaning up the .out files and zip it under logs directory.
# IBM
# Created
#For pdocap201/pdoca202 .out files for AOK
#1.... (0 Replies)
Discussion started by: mridul10_crj
0 Replies
7. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
8. AIX
Hello!
I have this infraestructure:
- 1 POWER7 with single VIOS on Site A.
- 1 POWER6 with single VIOS on Site B.
- 1 LPAR called NodeA as primary node for PowerHA 6.1 on Site A.
- 1 LPAR called NodeB as secondary (cold) node for PowerHA 6.1 on SiteB.
- 1 Storage DS4700 on Site A.
- 1... (8 Replies)
Discussion started by: enzote
8 Replies
9. UNIX for Advanced & Expert Users
Hello,
in one default UFS filesystem we have 8K block size (bsize) and 1K fragmentsize (fsize). At this scenary I thought all "FileSytem IO" will be 8K (or greater) but never smaller than the fragment size (1K). If a UFS fragment/blocksize is allwasy several ADJACENTS sectors on disk (in a ... (4 Replies)
Discussion started by: rarino2
4 Replies
10. Linux
Hi,
initially i will mount a image using loop device using below command
mount -n -o loop,noatime,ro -t squashfs /mnt/fsh/bt.img /opt/app/test
then "mount" reflects with below
/dev/loop0 on /opt/app/test type squashfs (ro,noatime)
i will then umount using below commnd, umount is... (0 Replies)
Discussion started by: successlin
0 Replies
LEARN ABOUT DEBIAN
guards
GUARDS(1) User Contributed Perl Documentation GUARDS(1)
NAME
guards - select from a list of files guarded by conditions
SYNOPSIS
guards [--prefix=dir] [--path=dir2:dir2:...] [--default=0|1] [-v|--invert-match] [--list|--check] [--config=file] symbol ...
DESCRIPTION
The script reads a configuration file that may contain so-called guards, file names, and comments, and writes those file names that satisfy
all guards to standard output. The script takes a list of symbols as its arguments. Each line in the configuration file is processed
separately. Lines may start with a number of guards. The following guards are defined:
+xxx Include the file(s) on this line if the symbol xxx is defined.
-xxx Exclude the file(s) on this line if the symbol xxx is defined.
+!xxx Include the file(s) on this line if the symbol xxx is not defined.
-!xxx Exclude the file(s) on this line if the symbol xxx is not defined.
- Exclude this file. Used to avoid spurious --check messages.
The guards are processed left to right. The last guard that matches determines if the file is included. If no guard is specified, the
--default setting determines if the file is included.
If no configuration file is specified, the script reads from standard input.
The --check option is used to compare the specification file against the file system. If files are referenced in the specification that do
not exist, or if files are not enlisted in the specification file warnings are printed. The --path option can be used to specify which
directory or directories to scan. Multiple directories are separated by a colon (":") character. The --prefix option specifies the
location of the files.
AUTHOR
Andreas Gruenbacher <agruen@suse.de> (SuSE Linux AG)
perl v5.14.2 2012-03-04 GUARDS(1)