Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: HACMP LV size is not reflecting
Operating Systems AIX HACMP LV size is not reflecting Post 302263712 by honeym210 on Tuesday 2nd of December 2008 10:03:14 AM
Old 12-02-2008
HACMP LV size is not reflecting
Hi

i increased the lv size using smit hacmp.
but, the new size is not reflecting.. why?.

the pp size is 512 MB. before it was 4 PP's. i increased to 10 PP's.
when i type df -m /xxx.. it is showing 2GB only.
see the info below..

root@db:/ > df -m /xxx/xxx
Filesystem MB blocks Free %Used Iused %Iused Mounted on
/dev/xxxx 2048.00 271.36 87% 13 1% /app/d2

root@db:/ > lslv xxxx
LOGICAL VOLUME: xxxxx VOLUME GROUP: ora_vg
LV IDENTIFIER: 002a127f00004c00000001028918726f.35 PERMISSION: read/write
VG STATE: active/complete LV STATE: opened/syncd
TYPE: jfs2 WRITE VERIFY: off
MAX LPs: 512 PP SIZE: 512 megabyte(s)
COPIES: 1 SCHED POLICY: parallel
LPs: 10 PPs: 10
STALE PPs: 0 BB POLICY: relocatable
INTER-POLICY: minimum RELOCATABLE: yes
INTRA-POLICY: middle UPPER BOUND: 32
MOUNT POINT: /xxx/xxx LABEL: /xxx/xxx
MIRROR WRITE CONSISTENCY: on/ACTIVE
EACH LP COPY ON A SEPARATE PV ?: yes
Serialize IO ?: NO

can someone help me on this..

thanks
 

10 More Discussions You Might Find Interesting

1. Solaris

command to find out total size of a specific file size (spread over the server)

hi all, in my server there are some specific application files which are spread through out the server... these are spread in folders..sub-folders..chid folders... please help me, how can i find the total size of these specific files in the server... (3 Replies)
Discussion started by: abhinov
3 Replies

2. Solaris

Why are the changes done to fs-root, not reflecting?

Hi all, I am trying to modify the file fs-root (on belenix). Here is the problem.. I just wanted to check whether any modifications done to the file will be reflected when its booted up, so just echoed a statement and saved it back to the cd and then booted it.. Unfortunately it did not... (0 Replies)
Discussion started by: wrapster
0 Replies

3. Solaris

mount point not reflecting actual utilization.

HI , I could see in df -k output that a mount point is 100% full. But i could not find any files with huge size that can be removed. So, i have umounted and mounted the filesystem again. Now, in my df -k output i could see that th eutilization is only 7%. Can anyone please suggest what... (3 Replies)
Discussion started by: sag71155
3 Replies

4. Programming

Problem in reflecting changes made on a JSP File

I make some changes in a JSP file but the changes do not reflect on tomcat server. In my server.xml 'reloadable' paramtere is set to true. I even treid restarting the server. The changes still not reflect. The changes do reflect in a day or two. am not sure why this is happening. Shall... (3 Replies)
Discussion started by: Shikha Agrawal
3 Replies

5. AIX

How to increase the filesystem size in HACMP

How to increase the filesystem size in HACMP. what is the difference between normal chfs command and increase the filesystem size in HACMP. (4 Replies)
Discussion started by: AIXlearner
4 Replies

6. Shell Programming and Scripting

The scripts not able to make the file to size 0, every times it go back to its original size

#!/bin/sh ########################################################################################################## #This script is being used for AOK application for cleaning up the .out files and zip it under logs directory. # IBM # Created #For pdocap201/pdoca202 .out files for AOK #1.... (0 Replies)
Discussion started by: mridul10_crj
0 Replies

7. AIX

HACMP does not start db2 after failover (db2nodes not getting modified by hacmp)

hi, when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies

8. AIX

Increase LUN size in AIX with VIOS and HACMP

Hello! I have this infraestructure: - 1 POWER7 with single VIOS on Site A. - 1 POWER6 with single VIOS on Site B. - 1 LPAR called NodeA as primary node for PowerHA 6.1 on Site A. - 1 LPAR called NodeB as secondary (cold) node for PowerHA 6.1 on SiteB. - 1 Storage DS4700 on Site A. - 1... (8 Replies)
Discussion started by: enzote
8 Replies

9. UNIX for Advanced & Expert Users

Physical disk IO size smaller than fragment block filesystem size ?

Hello, in one default UFS filesystem we have 8K block size (bsize) and 1K fragmentsize (fsize). At this scenary I thought all "FileSytem IO" will be 8K (or greater) but never smaller than the fragment size (1K). If a UFS fragment/blocksize is allwasy several ADJACENTS sectors on disk (in a ... (4 Replies)
Discussion started by: rarino2
4 Replies

10. Linux

Umount is not reflecting in losetup.

Hi, initially i will mount a image using loop device using below command mount -n -o loop,noatime,ro -t squashfs /mnt/fsh/bt.img /opt/app/test then "mount" reflects with below /dev/loop0 on /opt/app/test type squashfs (ro,noatime) i will then umount using below commnd, umount is... (0 Replies)
Discussion started by: successlin
0 Replies

LEARN ABOUT OPENSOLARIS

rdt_setmtu

rdt_setmtu(1M)						  System Administration Commands					    rdt_setmtu(1M)

NAME

       rdt_setmtu - set the MTU size in RSMRDT driver

SYNOPSIS

       /usr/cluster/bin/rdt_setmtu [MTU size]

DESCRIPTION

       The  rdt_setmtu command takes number of bytes as new MTU size and sets the global MTU size in RSMRDT driver. The RSMRDT driver uses the new
       MTU size for all the new instantiations of RSM connections. The existing RSM connections continue to use the old MTU size  value.  The  MTU
       size  should  be  a  multiple  of 64(0x40) bytes otherwise rdt_setmtu does not set the MTU size in RSMRDT driver and returns an error. The
       rdt_setmtu when running without any argument, displays the MTU size of RSMRDT driver.

       You can use this command only in the global zone.

OPERANDS

       The following operands are supported:

       MTU size 		   MTU size in bytes.

EXIT STATUS

       The following exit values are returned:

       0		   Successful completion.

       1		   An error occurred while setting MTU size.

       This utility writes an error message to stderr when it exits with non-zero status.

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes.

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWscrdt 		   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

SEE ALSO

       attributes(5)

Sun Cluster 3.2 						    30 Mar 2006 						    rdt_setmtu(1M)
All times are GMT -4. The time now is 06:04 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy