12-01-2008
Can you please run snoop and see if you can get some thing unusual?
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I am setting up a test server for actual 2 node servers which will be behind load balancer. I will not be using sun cluster at all. The test machine is installed with solaris 10.
I am not sure how to setup a test env of 2 nodes on only 1 node..may be creating 2 zones on test server will... (8 Replies)
Discussion started by: upengan78
8 Replies
2. Solaris
Hi All,
Kindly help me in configuring IPMP or guid me to some link, tried goggling however no luck.
Thanks in anticipation (1 Reply)
Discussion started by: kumarmani
1 Replies
3. Solaris
Probe-based IPMP active - active
Probe-based IPMP active - passive
Link-based only active -standby
????
What are differences between
Probe-based IPMP active - passive anddd
Link-based only active -standby
???!!!
For example in active active probe-based IPMP there are
lets... (6 Replies)
Discussion started by: samar
6 Replies
4. Shell Programming and Scripting
Hi,
I want to use a config file as the base file and parse over the values of country and city parameters in the config file and generate separate config files as explained below.
I will be using the config file as mentioned below:
(config.txt)
country:a,b
city:1,2
type:b1... (1 Reply)
Discussion started by: clazzic
1 Replies
5. Solaris
Please tell me how to configure IPMP in vmware
what is the basic working concept of IPMP.
please help me (1 Reply)
Discussion started by: sijocg
1 Replies
6. Solaris
Hi all
i had two interface
ce0 and ce5
but when i run the ifconfig, it show me alot of extra virtual interface, may i know how to remove it?
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0:... (2 Replies)
Discussion started by: SmartAntz
2 Replies
7. Shell Programming and Scripting
Hi I am new to shell scripting. There is a requirement to write a shell script to meet follwing needs.Prompt reply shall be highly appreciated.
script that will compare two config files and produce 2 outputs - actual config file and a report indicating changes made.
OS :Susi linux ver 10.3.
... (4 Replies)
Discussion started by: muraliinfy04
4 Replies
8. Solaris
Can any one please explain me the concept behind IPMP in solaris clustering.Basic explanation would be really appreciated...
Thanks in Advance
vks (2 Replies)
Discussion started by: vks47
2 Replies
9. Solaris
Dear All,
After configuring IPMP in 2 fresh Servers (T5520 and T2000) I can't login in any of them using SSH, I can login by serial console then I had to enable Telnet to access.
IPMP works fine.
This is the error in /var/adm/messages:
sshd: Failed password for lvalle from 172.28.12.95 port... (0 Replies)
Discussion started by: Luis Valle
0 Replies
10. Red Hat
Hi folks,
I am trying to configure Apache webserver and also a virtual host inside this webserver.
For Global server config: /var/www/html/index.html
For virtual host config: /var/www/virtual/index.html
Both client10 & www10 are pointing to 192.168.122.10 IP address.
BUT, MY... (1 Reply)
Discussion started by: freebird8z
1 Replies
LEARN ABOUT MOJAVE
iopending
iopending(1m) USER COMMANDS iopending(1m)
NAME
iopending - plot number of pending disk events. Uses DTrace.
SYNOPSIS
iopending [-c] [-d device] [-f filename] [-m mount_point] [interval [count]]
DESCRIPTION
This samples the number of disk events that are pending and plots a distribution graph. By doing this the "serialness" or "parallelness" of
disk behaviour can be distinguished. A high occurance of a pending value of more than 1 is an indication of saturation.
Since this uses DTrace, only users with root privileges can run this command.
OPTIONS
-c clear screen
-d device
instance name to snoop (eg, dad0)
-f filename
full pathname of file to snoop
-m mount_point
mountpoint for filesystem to snoop
EXAMPLES
Default output, print I/O summary every 1 second,
# iopending
Print 10 second samples,
# iopending 10
Print 12 x 5 second samples,
# iopending 5 12
Snoop events on the root filesystem only,
# iopending -m /
FIELDS
value number of pending events, 0 == idle
count number of samples @ 1000 Hz
load 1 min load average
disk_r total disk read Kb for sample
disk_w total disk write Kb for sample
IDEA
Dr Rex di Bona
DOCUMENTATION
See the DTraceToolkit for further documentation under the Docs directory. The DTraceToolkit docs may include full worked examples with ver-
bose descriptions explaining the output.
EXIT
iopending will run forever until Ctrl-C is hit, or the specified count is reached.
AUTHOR
Brendan Gregg [Sydney, Australia]
SEE ALSO
iosnoop(1M), iotop(1M), dtrace(1M)
version 0.60 Nov 01, 2005 iopending(1m)