11-26-2008
what is your current network configuration? how are other servers obtaining IP assignment?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi. I have installed Solaris 8 and I am trying to configure the network settings. For some reason every time I reboot, my card loses its configuration. I can run ifconfig and the only IP address bound to my card (on either interface) is 127.0.0.1. I can change that to a valid IP address on my... (8 Replies)
Discussion started by: Ask Me
8 Replies
2. IP Networking
Hi,
I need to configure the Network for a Sun Solaris systems.
The OS info is SunOS Sparsh 5.8 Generic_108528-13 Sun4u Sparc SUNW,Ultra-250.
Please do let me know, how shall I shart with & more in configuring the Network.
Below is the list of Network Configuration I need to Make
... (2 Replies)
Discussion started by: S.Vishwanath
2 Replies
3. HP-UX
Hi,
I have installed a HP-UX B.11.00 U 9000/800 Server in one of the domain. And I'm also able to telnet/ping into this server from systems in the same domain.
But I'm not able to telnet/ping into this server from a different domain.
So, what shoud need to do to achieve this... (6 Replies)
Discussion started by: S.Vishwanath
6 Replies
4. Solaris
hi again...
i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0.
there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies
5. Solaris
Can someone please point me in the correct direction of where I configure the network information on SunOS 5.8 server? (Searching SunSolve and Google have resulted in thousands of fixes for potential errors, but I can't find the general instructions, etc. for starting the process).
Thanks! (2 Replies)
Discussion started by: FredSmith
2 Replies
6. UNIX for Dummies Questions & Answers
I need to know what commands I will need to use to change a host name, IP Address, and network configurations (routerings, dns, etc) and a Unix SCO machine.
Also, if there is any short tutorials on using the commands, i would defiently like that information.
Thanks!!! (1 Reply)
Discussion started by: HandleX
1 Replies
7. SCO
I have a SCO 5.07 Server and I am trying to get it on my network. I have edited the /etc/hosts file and /etc/rc2.d/s99route . I has connectivity on the NIC card but not sure if I am forgetting another file. Thanks! (2 Replies)
Discussion started by: andrewd
2 Replies
8. UNIX for Dummies Questions & Answers
I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the
ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and
Route add default 192.168.1.xxx command to gain back my internet.
I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies
9. Solaris
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies
10. UNIX for Advanced & Expert Users
Hi all,
I got following configuration problem
I need to configure tiny network on openbsd
I got server1 with 3 interfaces vic0 em0 em1
The interface vic0 on server1 has follwoing IP 172.16.1.1
em0
firstly I would like to configure network under em0 (I have assigned to em0 following... (1 Reply)
Discussion started by: kvok
1 Replies
nets(4) Kernel Interfaces Manual nets(4)
NAME
nets - JOIN DHCP server database
DESCRIPTION
The nets file is employed by joind, the JOIN DHCP server, to tell it which networks to administer and the ranges of IP addresses available
for dynamic assignment on each of those networks.
FORMAT
Blank lines and lines beginning with the number sign (#) are ignored. Entries are separated from one another by newline characters.
Entries consist of three fields: the network number (expressed as an IP address), the IP address or name of a host running joind, which
dynamically configures clients on the network, and a range of available addresses for dynamic allocation to hosts on the net. The range is
expressed as a pair of IP addresses separated with a dash (-). There must be no whitespace separating the dash from the IP addresses.
Several servers may administer a single network, and a single server may administer several networks. Each network-server pair may have
several ranges of IP addresses available for dynamic allocation. The network and server IP addresses do not have to be repeated for each
entry. A line containing a single field is assumed to be an IP range with the same server and network as the previous entry: a line of two
fields is assumed to be a server address and IP range with the same network as the preceding entry.
The ranges of addresses served by each cooperating server must be disjoint. This condition is checked by the server on startup.
RELATED INFORMATION
joind(8), join.ipaddresses(4) delim off
nets(4)