11-26-2008
Hi Duke,
At the last i have rebooted the machine.
But Is the svcadm will work in Multiusermode
Thanks
Rj
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I am setting up a test server for actual 2 node servers which will be behind load balancer. I will not be using sun cluster at all. The test machine is installed with solaris 10.
I am not sure how to setup a test env of 2 nodes on only 1 node..may be creating 2 zones on test server will... (8 Replies)
Discussion started by: upengan78
8 Replies
2. Solaris
Hi All,
Kindly help me in configuring IPMP or guid me to some link, tried goggling however no luck.
Thanks in anticipation (1 Reply)
Discussion started by: kumarmani
1 Replies
3. Solaris
Probe-based IPMP active - active
Probe-based IPMP active - passive
Link-based only active -standby
????
What are differences between
Probe-based IPMP active - passive anddd
Link-based only active -standby
???!!!
For example in active active probe-based IPMP there are
lets... (6 Replies)
Discussion started by: samar
6 Replies
4. Shell Programming and Scripting
Hi,
I want to use a config file as the base file and parse over the values of country and city parameters in the config file and generate separate config files as explained below.
I will be using the config file as mentioned below:
(config.txt)
country:a,b
city:1,2
type:b1... (1 Reply)
Discussion started by: clazzic
1 Replies
5. Solaris
Please tell me how to configure IPMP in vmware
what is the basic working concept of IPMP.
please help me (1 Reply)
Discussion started by: sijocg
1 Replies
6. Solaris
Hi all
i had two interface
ce0 and ce5
but when i run the ifconfig, it show me alot of extra virtual interface, may i know how to remove it?
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0:... (2 Replies)
Discussion started by: SmartAntz
2 Replies
7. Shell Programming and Scripting
Hi I am new to shell scripting. There is a requirement to write a shell script to meet follwing needs.Prompt reply shall be highly appreciated.
script that will compare two config files and produce 2 outputs - actual config file and a report indicating changes made.
OS :Susi linux ver 10.3.
... (4 Replies)
Discussion started by: muraliinfy04
4 Replies
8. Solaris
Can any one please explain me the concept behind IPMP in solaris clustering.Basic explanation would be really appreciated...
Thanks in Advance
vks (2 Replies)
Discussion started by: vks47
2 Replies
9. Solaris
Dear All,
After configuring IPMP in 2 fresh Servers (T5520 and T2000) I can't login in any of them using SSH, I can login by serial console then I had to enable Telnet to access.
IPMP works fine.
This is the error in /var/adm/messages:
sshd: Failed password for lvalle from 172.28.12.95 port... (0 Replies)
Discussion started by: Luis Valle
0 Replies
10. Red Hat
Hi folks,
I am trying to configure Apache webserver and also a virtual host inside this webserver.
For Global server config: /var/www/html/index.html
For virtual host config: /var/www/virtual/index.html
Both client10 & www10 are pointing to 192.168.122.10 IP address.
BUT, MY... (1 Reply)
Discussion started by: freebird8z
1 Replies
statd(1M) System Administration Commands statd(1M)
NAME
statd - network status monitor
SYNOPSIS
/usr/lib/nfs/statd
DESCRIPTION
statd is an intermediate version of the status monitor. It interacts with lockd(1M) to provide the crash and recovery functions for the
locking services on NFS. statd keeps track of the clients with processes which hold locks on a server. When the server reboots after a
crash, statd sends a message to the statd on each client indicating that the server has rebooted. The client statd processes then inform
the lockd on the client that the server has rebooted. The client lockd then attempts to reclaim the lock(s) from the server.
statd on the client host also informs the statd on the server(s) holding locks for the client when the client has rebooted. In this case,
the statd on the server informs its lockd that all locks held by the rebooting client should be released, allowing other processes to lock
those files.
lockd is started by automountd(1M), mount_nfs(1M), and share(1M) if NFS automounts are needed.
FILES
/var/statmon/sm lists hosts and network addresses to be contacted after a reboot
/var/statmon/sm.bak lists hosts and network addresses that could not be contacted after last reboot
/var/statmon/state includes a number which changes during a reboot
/usr/include/rpcsvc/sm_inter.x contains the rpcgen source code for the interface services provided by the statd daemon.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWnfscu |
+-----------------------------+-----------------------------+
SEE ALSO
svcs(1), automountd(1M), lockd(1M), mount_nfs(1M), share(1M), svcadm(1M), attributes(5), smf(5)
System Administration Guide: IP Services
NOTES
The crash of a server is only detected upon its recovery.
The statd service is managed by the service management facility, smf(5), under the service identifier:
svc:/network/nfs/status
Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser-
vice's status can be queried using the svcs(1) command.
If it is disabled, it will be enabled by mount_nfs(1M), share_nfs(1M), and automountd(1M) unless its application/auto_enable prop-
erty is set to false.
SunOS 5.10 18 Nov 2004 statd(1M)