Sponsored Content
Full Discussion: IPMP config
Operating Systems Solaris IPMP config Post 302261820 by DukeNuke2 on Tuesday 25th of November 2008 03:31:17 PM
Old 11-25-2008
what is the output of "dladm show-dev"?
 

10 More Discussions You Might Find Interesting

1. Solaris

IPMP/zones config how for this case ,urgent

Hi I am setting up a test server for actual 2 node servers which will be behind load balancer. I will not be using sun cluster at all. The test machine is installed with solaris 10. I am not sure how to setup a test env of 2 nodes on only 1 node..may be creating 2 zones on test server will... (8 Replies)
Discussion started by: upengan78
8 Replies

2. Solaris

Ipmp

Hi All, Kindly help me in configuring IPMP or guid me to some link, tried goggling however no luck. Thanks in anticipation (1 Reply)
Discussion started by: kumarmani
1 Replies

3. Solaris

IPMP questions

Probe-based IPMP active - active Probe-based IPMP active - passive Link-based only active -standby ???? What are differences between Probe-based IPMP active - passive anddd Link-based only active -standby ???!!! For example in active active probe-based IPMP there are lets... (6 Replies)
Discussion started by: samar
6 Replies

4. Shell Programming and Scripting

parsing config file to create new config files

Hi, I want to use a config file as the base file and parse over the values of country and city parameters in the config file and generate separate config files as explained below. I will be using the config file as mentioned below: (config.txt) country:a,b city:1,2 type:b1... (1 Reply)
Discussion started by: clazzic
1 Replies

5. Solaris

ipmp testing

Please tell me how to configure IPMP in vmware what is the basic working concept of IPMP. please help me (1 Reply)
Discussion started by: sijocg
1 Replies

6. Solaris

IPMP problem

Hi all i had two interface ce0 and ce5 but when i run the ifconfig, it show me alot of extra virtual interface, may i know how to remove it? # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 ce0:... (2 Replies)
Discussion started by: SmartAntz
2 Replies

7. Shell Programming and Scripting

Shell script that will compare two config files and produce 2 outputs 1)actual config file 2)report

Hi I am new to shell scripting. There is a requirement to write a shell script to meet follwing needs.Prompt reply shall be highly appreciated. script that will compare two config files and produce 2 outputs - actual config file and a report indicating changes made. OS :Susi linux ver 10.3. ... (4 Replies)
Discussion started by: muraliinfy04
4 Replies

8. Solaris

Solaris IPMP

Can any one please explain me the concept behind IPMP in solaris clustering.Basic explanation would be really appreciated... Thanks in Advance vks (2 Replies)
Discussion started by: vks47
2 Replies

9. Solaris

Can't login using ssh after IPMP config.

Dear All, After configuring IPMP in 2 fresh Servers (T5520 and T2000) I can't login in any of them using SSH, I can login by serial console then I had to enable Telnet to access. IPMP works fine. This is the error in /var/adm/messages: sshd: Failed password for lvalle from 172.28.12.95 port... (0 Replies)
Discussion started by: Luis Valle
0 Replies

10. Red Hat

Apache virtual host config vs global config problem

Hi folks, I am trying to configure Apache webserver and also a virtual host inside this webserver. For Global server config: /var/www/html/index.html For virtual host config: /var/www/virtual/index.html Both client10 & www10 are pointing to 192.168.122.10 IP address. BUT, MY... (1 Reply)
Discussion started by: freebird8z
1 Replies
ntxn(7D)							      Devices								  ntxn(7D)

NAME
ntxn - NetXen 10/1 Gigabit Ethernet network driver SYNOPSIS
/dev/ntxn* DESCRIPTION
The ntxn 10/1 Gigabit Ethernet driver is a multi-threaded, loadable, clonable, GLD-based STREAMS driver supporting the Data Link Provider Interface, dlpi(7P), on NetXen 10/1 Gigabit Ethernet controllers. The ntxn driver functions include chip initialization, frames transmit and receive, promiscuous and multicast support, TCP and UDP checksum off-load (IPv4) and 9600 bytes jumbo frame. The ntxn driver and hardware support the 10GBASE CX4, 10GBASE-SR/W, LR/W, and 10/100/1000BASE-T physical layers. APPLICATION PROGRAMMING INTERFACE
The cloning character-special device, /dev/ntxn, is used to access all NetXen devices installed within the system. The ntxn driver is managed by the dladm(1M) command line utility, which allows VLANs to be defined on top of ntxn instances and for ntxn instances to be aggregated. See dladm(1M) for more details. The values returned by the driver in the DL_INFO_ACK primitive in response to your DL_INFO_REQ are: o Maximum SDU is 9600. o Minimum SDU is 0. o DLSAP address length is 8. o MAC type is DL_ETHER. o SAP (Service Access Point) length value is -2, meaning the physical address component is followed immediately by a 2-byte SAP component within the DLSAP address. o Broadcast address value is the Ethernet/IEEE broadcast address (FF:FF:FF:FF:FF:FF). CONFIGURATION
By default, the ntxn driver works without any configuration file. FILES
/dev/ntxn* Special character device. /kernel/drv/ntxn 32-bit device driver (x86). /kernel/drv/amd64/ntxn 64-bit device driver (x86). /kernel/drv/ntxn.conf Configuration file. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------------------------------------+ |ATTRIBUTE TYPE ATTRIBUTE VALUE | |Availability SUNWntxn | |Architecture x86 | |Interface Stability Committed | +-----------------------------------------------------------+ SEE ALSO
dladm(1M), ndd(1M), netstat(1M), driver.conf(4), attributes(5), streamio(7I), dlpi(7P) Writing Device Drivers STREAMS Programming Guide Network Interfaces Programmer's Guide SunOS 5.11 13 Oct 2008 ntxn(7D)
All times are GMT -4. The time now is 11:02 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy