Sponsored Content
Full Discussion: Route to nowhere?
Special Forums IP Networking Route to nowhere? Post 302259954 by monroedoug on Wednesday 19th of November 2008 10:29:26 AM
Old 11-19-2008
Route to nowhere?

Hi,

HP-UX 11iV2, but it's probably universal (tcp/ip)

I have a production and a test server. The test server gets the application updated nightly from the production server software. The application accesses a set of process servers on a separate subnet (192.163.22.30,31,32), but reachable via the default route. The process server IP addresses are hard coded into the application (no, I can't use the hostname).

I want the test server to NOT be able to access these IP addresses. I tried setting up a non-existent route, but HP-UX tests to make sure the destination is reachable, and won't set it up.

Any ideas?

Thanks
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Disappearing route

I have a route that disappears when the server is rebooted. to get the route back I do: route add 65.x.x.x 10.0.x.x I go to cd /etc/inet vi config and the route is in place Anybody might know what is happening? (4 Replies)
Discussion started by: jrmontg
4 Replies

2. IP Networking

static route ?

Hi, I have a machine that sits on 10.2 network. I need to ssh from this to another box that is on both 10.125 & 10.140 VLANs what should I need to do? Thanks! (3 Replies)
Discussion started by: chaandana
3 Replies

3. IP Networking

Do I need to add a route??

I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0. My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network. My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies

4. Solaris

permanent route

How do I make a route permanent, other than default route on a Solaris server? (1 Reply)
Discussion started by: jontom
1 Replies

5. Solaris

SOLARIS does not route

hi, i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,... (4 Replies)
Discussion started by: bong02
4 Replies

6. Solaris

Adding new Route

Hi, I am trying to add route command in SunOS machine but it is not successful : route add -host 10.31.251.47 -gateway 10.31.251.0 -interface ce0 this command fails with an error "lo0:1: bad value" I want to add a route to 10.31.251.47 that picks 10.31.251.0 as the gateway via the... (1 Reply)
Discussion started by: jaygamini
1 Replies

7. UNIX for Dummies Questions & Answers

Static Route

Hi, Request you to please tell me the command or the process to add the static route in redhat linux. Thanks in Advance. Regards Arun (2 Replies)
Discussion started by: Arun.Kakarla
2 Replies

8. Red Hat

No route to host

I get below error when using telnet and ssh ?? Why ? the ip address of linux server is 10.155.25.22 =tstgcota ?? # netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.75.0 0.0.0.0 255.255.255.0 U 0 0... (6 Replies)
Discussion started by: chuikingman
6 Replies

9. Shell Programming and Scripting

cut route

Hola, Tengo una cadena de una ruta y quiero cortar la ultima parte sin la extension Example /home/Desktop/example/audio.html Yo quiero solo "audio". Muchas gracias (4 Replies)
Discussion started by: uri_crack
4 Replies

10. IP Networking

route add

I have built a new linux server, via a iLo connection. and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty. Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
DUMP_SOCKDFR(8) 					      System Manager's Manual						   DUMP_SOCKDFR(8)

NAME
dump_sockdfr - Display contents of frozen route file for SOCKS server SYNOPSIS
dump_sockdfr [infile] DESCRIPTION
dump_sockdfr reads in a frozen route file for the SOCKS server and produces a listing of its contents on the standard output. The argument is optional; if omitted, /etc/sockd.fr is assumed. The frozen route file is produced by make_sockdfr and is essentially the memory image of the parsed route file. Using the frozen route file can reduce the start-up delay of the SOCKS server program since it no longer has to parse the file contents. When the SOCKS server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every time after you modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file. FILES
/etc/sockd.fr, /etc/sockd.route SEE ALSO
make_sockdfr(8), sockd.fr(5), sockd.route(5) AUTHOR
Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com May 6, 1996 DUMP_SOCKDFR(8)
All times are GMT -4. The time now is 04:42 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy