Sponsored Content
Full Discussion: 1 or 2 Fiber cables?
Operating Systems Solaris 1 or 2 Fiber cables? Post 302259236 by ikorolev on Monday 17th of November 2008 02:06:23 PM
Old 11-17-2008
Quote:
Originally Posted by Sunb3
I'd connect the Server to the Storedge with a fiber cable but I' m in doubt becouse I don't know if using 1 or 2 fiber cable.
Could you provide me any solution?
Could you explain me the reason?
If you using 2 cables and enable multipating software - stms (mpxio), then
in cases one of cables or one of controllers, or one of ports on disk array is broken - your server will work.
 

10 More Discussions You Might Find Interesting

1. Solaris

Scsi cables - which ones?

Is there any specific scsi cables that you need to get when connecting a tape drive or external storage or does one type of cable fit all? ie. I can buy the following: HD68 to HD68 with Ferrites supports S-E Ultra/Wide transfer rates. But will this work for tape drives and storage? I... (1 Reply)
Discussion started by: frustrated1
1 Replies

2. IP Networking

fc cables

hi friends, we are using fc cables and fc switches,u might be aware of the cost factor of it so just wanted to know that Why do we need FC switches and fiber-optic cables? Is it not possible to use, say, twisted-pair copper cables instead of fiber-optic cables, and achieve almost comparable... (3 Replies)
Discussion started by: mxms755
3 Replies

3. Solaris

Identify fiber card

All, Is there a way to identify which fiber card (brand) I have in my system? I believe my solaris 8 box has an LP9002LE card, I'm just not 100% sure. Thanks, Kevin (4 Replies)
Discussion started by: kjbaumann
4 Replies

4. AIX

fiber with 4GB

Hi, It's my first time I will use a 4BG fiber with two ports on one card. I used only one port 2GB before. What will be the drivers I need to install on my AIX5.3? Is the two ports going to be just one line? Or I can use the other ports on another connection. Thanks in advance, itik (1 Reply)
Discussion started by: itik
1 Replies

5. AIX

aix with two fiber

Hi, I got an advise from an old colleague that it's not recommended to have a two fiber for performance purposes on aix. Only use it for redundancy or rdac. Is that true? I was thinking to divide the use of two fiber with the 8 vg so I each one would have 4 vg to serve. Is there anyone... (4 Replies)
Discussion started by: itik
4 Replies

6. Solaris

Solaris 10 new fiber connected tape

Hello all, how can i see configured fc tapes in solaris system and how can i install a new fc shared tape device , thanks Best Regards (2 Replies)
Discussion started by: bogacd
2 Replies

7. Solaris

SUNFIRE V240 procedure to shutdown with safety in order to replace power cables

Question: Which commands to use to shutdown with safety the server; (2 Replies)
Discussion started by: doudou2012
2 Replies

8. Hardware

Flat cables vs normal circular cables

Do flat cables have any advantage over normal circular cables? I was looking at this. 6ft 2M Flat USB Sync Data Cable Charger Cord for iPhone4 4S 3G iPad1 2 3 Orange | eBay (2 Replies)
Discussion started by: cokedude
2 Replies

9. War Stories

Following Cables for Fun!

Hi Folks, I came accross this picture taken a number of years ago now, I just thought I'd share it with you guys. We were in the process of removing equipment from the Data Centre and had followed the cable through to this area, where one of the old patch areas had been. When we lifted the... (2 Replies)
Discussion started by: gull04
2 Replies

10. IP Networking

What RJ11 Cables Should I Use?

Hello All, I have a project I'm working on which involves a linux PC and a USB (*dialup) Modem in a remote location for telnet'ing to that PC by phone when the Ethernet connection is down. I have already purchased the USB modems I need and some dumb phones for line testing... Now I'm trying... (7 Replies)
Discussion started by: mrm5102
7 Replies
NEWAPC(8)						      Network UPS Tools (NUT)							 NEWAPC(8)

NAME
newapc - Driver for American Power Conversion Smart Protocol UPS equipment NOTE
This man page only documents the hardware-specific features of the newapc driver. For information about the core driver, see nutupsdrv(8). SUPPORTED HARDWARE
newapc should recognize all recent APC models that use a serial protocol at 2400 bps. This is primarily the Smart-UPS, Matrix-UPS and Back-UPS Pro lines. Older APC models may work better with the apcsmart driver. The driver attempts to support every bell and whistle of the APC reporting interface, whether or not this is strictly sensible. Some older hardware may only report a handful of variables. This is usually not a bug - they just don't support anything else. CABLING
This driver expects to see a 940-0024C cable or a clone by default. You can switch to the 940-0095B dual-mode cable support with the cable= definition described below. If your 940-0024C cable is broken or missing, use this diagram to build a clone: http://www.exploits.org/nut/library/cables/940-0024C.jpg EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5): cable=940-0095B Configure the serial port for the APC 940-0095B dual-mode cable. sdtype=num Use shutdown type num, according to this table: 0: soft shutdown or powerdown, depending on battery status 1: soft shutdown followed by powerdown 2: instant power off 3: power off with grace period Modes 0 and 1 will power up the load when power returns. Modes 2 and 3 will keep the load turned off when the power returns. BUGS
Some older APC UPS models return bogus data in the status register during a front panel test. This is usually detected and discarded, but some other unexpected values have occasionally slipped through. AUTHOR
Nigel Metheringham <Nigel.Metheringham@Intechnology.co.uk> (drawing heavily on the apcsmart driver by Russell Kroll). SEE ALSO
The core driver: nutupsdrv(8) The apcsmart driver: apcsmart(8) Internet resources: The NUT (Network UPS Tools) home page: http://www.exploits.org/nut/ NUT mailing list archives and information: http://lists.exploits.org/ Tue Oct 22 2002 NEWAPC(8)
All times are GMT -4. The time now is 02:45 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy