Sponsored Content
Full Discussion: 1 or 2 Fiber cables?
Operating Systems Solaris 1 or 2 Fiber cables? Post 302259054 by Sunb3 on Monday 17th of November 2008 06:15:27 AM
Old 11-17-2008
1 or 2 Fiber cables?

Hi Community,

I'm working on Solaris 10 installation with 1 Server V490 and 1 StoredgeTek 3510 (Standalone configuration).

I'd connect the Server to the Storedge with a fiber cable but I' m in doubt becouse I don't know if using 1 or 2 fiber cable.

Could you provide me any solution?

Could you explain me the reason?

Thank you very much!
 

10 More Discussions You Might Find Interesting

1. Solaris

Scsi cables - which ones?

Is there any specific scsi cables that you need to get when connecting a tape drive or external storage or does one type of cable fit all? ie. I can buy the following: HD68 to HD68 with Ferrites supports S-E Ultra/Wide transfer rates. But will this work for tape drives and storage? I... (1 Reply)
Discussion started by: frustrated1
1 Replies

2. IP Networking

fc cables

hi friends, we are using fc cables and fc switches,u might be aware of the cost factor of it so just wanted to know that Why do we need FC switches and fiber-optic cables? Is it not possible to use, say, twisted-pair copper cables instead of fiber-optic cables, and achieve almost comparable... (3 Replies)
Discussion started by: mxms755
3 Replies

3. Solaris

Identify fiber card

All, Is there a way to identify which fiber card (brand) I have in my system? I believe my solaris 8 box has an LP9002LE card, I'm just not 100% sure. Thanks, Kevin (4 Replies)
Discussion started by: kjbaumann
4 Replies

4. AIX

fiber with 4GB

Hi, It's my first time I will use a 4BG fiber with two ports on one card. I used only one port 2GB before. What will be the drivers I need to install on my AIX5.3? Is the two ports going to be just one line? Or I can use the other ports on another connection. Thanks in advance, itik (1 Reply)
Discussion started by: itik
1 Replies

5. AIX

aix with two fiber

Hi, I got an advise from an old colleague that it's not recommended to have a two fiber for performance purposes on aix. Only use it for redundancy or rdac. Is that true? I was thinking to divide the use of two fiber with the 8 vg so I each one would have 4 vg to serve. Is there anyone... (4 Replies)
Discussion started by: itik
4 Replies

6. Solaris

Solaris 10 new fiber connected tape

Hello all, how can i see configured fc tapes in solaris system and how can i install a new fc shared tape device , thanks Best Regards (2 Replies)
Discussion started by: bogacd
2 Replies

7. Solaris

SUNFIRE V240 procedure to shutdown with safety in order to replace power cables

Question: Which commands to use to shutdown with safety the server; (2 Replies)
Discussion started by: doudou2012
2 Replies

8. Hardware

Flat cables vs normal circular cables

Do flat cables have any advantage over normal circular cables? I was looking at this. 6ft 2M Flat USB Sync Data Cable Charger Cord for iPhone4 4S 3G iPad1 2 3 Orange | eBay (2 Replies)
Discussion started by: cokedude
2 Replies

9. War Stories

Following Cables for Fun!

Hi Folks, I came accross this picture taken a number of years ago now, I just thought I'd share it with you guys. We were in the process of removing equipment from the Data Centre and had followed the cable through to this area, where one of the old patch areas had been. When we lifted the... (2 Replies)
Discussion started by: gull04
2 Replies

10. IP Networking

What RJ11 Cables Should I Use?

Hello All, I have a project I'm working on which involves a linux PC and a USB (*dialup) Modem in a remote location for telnet'ing to that PC by phone when the Ethernet connection is down. I have already purchased the USB modems I need and some dumb phones for line testing... Now I'm trying... (7 Replies)
Discussion started by: mrm5102
7 Replies
LIEBERT(8)							    NUT Manual								LIEBERT(8)

NAME
liebert - Driver for Liebert contact-closure UPS equipment NOTE
This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8). SUPPORTED HARDWARE
This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver. EXTRA ARGUMENTS
This driver does not support any extra settings in the ups.conf(5). BUGS
This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable. You may have to build another cable with DTR connected through to the UPS for it to work. There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a fundamental limitation of any contact-closure driver. SEE ALSO
The core driver: nutupsdrv(8) Internet resources: The NUT (Network UPS Tools) home page: http://www.networkupstools.org/ Network UPS Tools 05/21/2012 LIEBERT(8)
All times are GMT -4. The time now is 06:26 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy