11-15-2008
start the webbrowser from the linux mashine. you can route the display to your locel mashine and do the update this way...
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Alright we have a strange problem that i never encountered.
We have a V445 Sun Fire we are trying to install it via a tadpole laptop (jumpstart laptop) the v445 takes the flash just fine, but we get an error upon reboot saying unable to locate boot device. Well our SUN guru said we need to... (2 Replies)
Discussion started by: deaconf19
2 Replies
2. Solaris
I have solaris X4500 with ILOM version 1.1.1. I want to update the firmware. I know that we need to use
load -source tftp://tftpserver/image file
But I do not understand what is the IP address of the tftp server that we need to type in there.
Kindly, help me with this.
Thank you (5 Replies)
Discussion started by: bharu_sri
5 Replies
3. Solaris
I get an error message when I try to upgrade the firmware. The error message is displayed below.
Image has no uboot. DO NOT RESET OR YOU WILL BRICK THE ILOM. Please retry with the correct image
I do not understand anything about this message. May I know what does it mean ? How can I get rid... (6 Replies)
Discussion started by: bharu_sri
6 Replies
4. Solaris
when I type start /SP/console... the console shows up but i cannot type anything over there. I do not understand what might be the reason for that.
-> start /SP/console
Are you sure you want to start /SP/console (y/n)? y
Serial console started. To stop, type ESC (
I pressed enter many... (8 Replies)
Discussion started by: bharu_sri
8 Replies
5. Solaris
I have X4500 running solaris 10 with 5.10 version. The ILOM version is 1.1.1 and I want to upgrade the firmware. I setup the TFTP server on my machine using the following link.
A P P E N D I X C - Updating the Firmware
I could install the tftp server and could transfer a file as well. When I... (1 Reply)
Discussion started by: bharu_sri
1 Replies
6. Solaris
Hi guys I have a Sun Fire X4500 running Solaris 10 OS. It has 48 TB Hard Disk. I need to format it and make 3 partitions. Could someone give me a link or help me with this.
Thank you (1 Reply)
Discussion started by: bharu_sri
1 Replies
7. AIX
this error is appear in my server . please can anyone help me with it .
IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION
BFE4C025 0323100711 P H sysplanar0 UNDETERMINED ERROR
BFE4C025 0323100611 P H sysplanar0 UNDETERMINED ERROR
BFE4C025 0323090711 P H sysplanar0 ... (4 Replies)
Discussion started by: thecobra151
4 Replies
8. SuSE
Hi all
We've had an issue over the weekend when one of the SUSE Linux Enterprise Server 11 hung and had to be rebooted. The thing is that I got the ticket alert for a FS exceeding its usage at about 22:41:49 PM on 23 March. I checked the dmesg, the messages log and the boot.msg but all I found... (1 Reply)
Discussion started by: hedkandi
1 Replies
9. AIX
Hello AIX experts,
I have 7038-6M2 server, its operating system is AIX 5.2, and its firmware is 3K041021
After some searching on net, I tried to update its firmware level to 3K080425, so I downloaded the required rpm, and followed the steps.
After rebooting the server, it stopped and an error... (6 Replies)
Discussion started by: Mohannad
6 Replies
LEARN ABOUT NETBSD
route.conf
ROUTE.CONF(5) BSD File Formats Manual ROUTE.CONF(5)
NAME
route.conf -- static routes config file
DESCRIPTION
The route.conf file is read by the staticroute rc.d script during system start-up and shutdown, and is intended for adding and removing
static routes.
FILE FORMAT
Lines starting with a hash ('#') are comments and ignored. Lines starting with a plus sign ('+') are run during start-up, while lines start-
ing with a minus sign ('-') are run during system shutdown. If a line starts with a '!', the rest of the line will get evaluated as a shell
script fragment. All other lines are passed to route(8). During start-up, they are passed behind a ``route add -'' command and during shut-
down behind a ``route delete -'' command.
FILES
/etc/route.conf The route.conf file resides in /etc.
/etc/rc.d/staticroute
rc.d(8) script that parses route.conf.
EXAMPLES
In this example, the interface for the desired routing changes is set, the IP address on that interface is determined, and a route is added
during startup, or deleted during system shutdown.
# Set interface and determine current IP address for added route.
!ifname=bnx0
!ipaddr=$(/sbin/ifconfig ${ifname} | awk '$1 == "inet" {print $2}')
net 10.10.1 -interface ${ipaddr}
In this example, IP forwarding is turned on during start-up, and a static route added for 192.168.2.0. During system shutdown, the route is
removed and IP forwarding turned off.
# Turn on/off IP forwarding.
+sysctl -w net.inet.ip.forwarding=1
-sysctl -w net.inet.ip.forwarding=0
net 192.168.2.0 -netmask 255.255.255.0 192.168.150.2
SEE ALSO
rc.conf(5), rc(8), route(8)
BSD
May 1, 2012 BSD