Sponsored Content
Operating Systems Solaris Install Solaris 10 with an internal StorageTek SAS HBA Raid card Post 302257823 by pressy on Thursday 13th of November 2008 06:31:35 AM
Old 11-13-2008
i installed that combination two weeks ago.... you will see the disks after you've configured the raid....
you can download an install image from intel, with that liveCD you can configure your RAID-HBA using the arcconf command (or the GUI):
Sun StorageTek* SAS RAID HBA, Internal Downloads

It would be a good idea to use the latest solaris 10 10/08 update 6, this version already includes the HBA-Driver Module (aac... otherwise you will have to jumpstart that system with that specific driver, like mentioned in that documentation)

It is recommended to use the lastest firmware, i had problems with an old firmware seeing the HBA in the RAID-GUI. i also did that with the liveCD:
Code:
root@system # ls /tmp/fw
as580501.ufi  as580503.ufi  as580505.ufi  as580507.ufi
as580502.ufi  as580504.ufi  as580506.ufi

root@system # arcconf ROMUPDATE all /tmp/fw/as5805
Controllers found: 1

You must restart the system for firmware updates to take effect.

Are you sure you want to continue?
Press y, then ENTER to continue or press ENTER to abort: y

Updating controller 1 firmware...Succeeded
A new software image has been applied to controller 1.


Command completed successfully.

REBOOT

root@system # arcconf GETVERSION
Controllers found: 1
Controller #1
==============
Firmware           : 5.2-0 (15825)
Staged Firmware    : 5.2-0 (15825)
BIOS               : 5.2-0 (15825)
Driver             : 2.2-16 (15817)
Boot Flash         : 5.2-0 (15825)


Command completed successfully.

regards
- PRESSY
 

8 More Discussions You Might Find Interesting

1. Solaris

istall sas raid HBA internal card

I need to install a raid HBA internal card on a T5240. The reason is I have more drives and the current mother board controller does not support more than 4 drives. My question is I have raidctl set up on current drives. If I install new HBA card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies

2. UNIX for Advanced & Expert Users

Sun internal disks and HBA card

I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage. Would I sacrifice performance if I use the same HBA? Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies

3. Solaris

installing solaris with StorageTek SAS RAID Internal HBA

i was given a task which needs to perform a raid 1 on the boot disk, and 4 other disks on raid 10. Is there any other alternative in installing solaris 10 other than through network installation?will be using solaris update 6. while reading through the user guide i got pretty confuse. ... (1 Reply)
Discussion started by: monstar1407
1 Replies

4. Solaris

T5240 and Internal SAS RAID Configuration help

Dear Friends, I need to configure T5240 with Internal SAS RAID HBA(SG-XPCIESAS-R-INT-Z).. T5240 uses 8 hard disks... From the documents of RAID card I have found that I need to create a jump start server to include three packages SUNWaac, StorMan, SUNWgccruntime if Im using solaris10 5/08... ... (5 Replies)
Discussion started by: nicktrix
5 Replies

5. Solaris

After update Solaris version, HBA driver still need to install?

Hi all I had update a server from Solaris 8 to Solaris 10 is it the HBA driver still need to reinstall? since i can get the driver info as below: root@sgerpdev # fcinfo hba-port HBA Port WWN: 21000003ba9b58a3 OS Device Name: /dev/cfg/c1 Manufacturer: QLogic Corp. ... (1 Reply)
Discussion started by: SmartAntz
1 Replies

6. Solaris

How to enable hba port of a two port hba card

Hi, i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port. ---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ---------- please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies

7. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies

8. Solaris

Solaris 10: how to disable an unused HBA card

Dear all, I have a new Oracle Blade X4-2B server, running Solaris 10. The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing. My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
MPT(4)							   BSD Kernel Interfaces Manual 						    MPT(4)

NAME
mpt -- LSI Fusion-MPT SCSI/Fibre Channel driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device scbus device mpt Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): mpt_load="YES" DESCRIPTION
The mpt driver provides support for the LSI Logic Fusion-MPT family of SCSI, Fibre Channel and SAS controllers. HARDWARE
The following controllers are supported by the mpt driver: o LSI Logic 53c1030, LSI Logic LSI2x320-X (Single and Dual Ultra320 SCSI) o LSI Logic AS1064, LSI Logic AS1068 (SAS/SATA) o LSI Logic FC909 (1Gb/s Fibre Channel) o LSI Logic FC909A (Dual 1Gb/s Fibre Channel) o LSI Logic FC919, LSI Logic 7102XP-LC (Single 2Gb/s Fibre Channel) o LSI Logic FC929, LSI Logic FC929X, LSI Logic 7202XP-LC (Dual 2Gb/s Fibre Channel) o LSI Logic FC949X (Dual 4Gb/s Fibre Channel) o LSI Logic FC949E, LSI Logic FC949ES (Dual 4Gb/s Fibre Channel PCI-Express) The Ultra 320 SCSI controller chips supported by the mpt driver can be found onboard on many systems including: o Dell PowerEdge 1750 thru 2850 o IBM eServer xSeries 335 These systems also contain Integrated Raid Mirroring and Integrated Raid Mirroring Enhanced which this driver also supports. The SAS controller chips are also present on many new AMD/Opteron based systems, like the Sun 4100. Note that this controller can drive both SAS and SATA drives or a mix of them at the same time. The Integrated Raid Mirroring available for these controllers is poorly supported at best. The Fibre Channel controller chipset are supported by a broad variety of speeds and systems. The Apple Fibre Channel HBA is in fact the FC949ES card. This driver also supports target mode for Fibre Channel cards. This support may be enabled by setting the desired role of the core via the LSI Logic firmware utility that establishes what roles the card can take on - no separate compilation is required. SEE ALSO
cd(4), ch(4), da(4), pci(4), sa(4), scsi(4), targ(4), mptutil(8), gmultipath(8) LSI Logic Website, http://www.lsilogic.com/. HISTORY
The mpt driver first appeared in FreeBSD 4.6. AUTHORS
The mpt driver was originally written for FreeBSD by Greg Ansley and marginally improved upon by Matt Jacob <mjacob@FreeBSD.org>. Justin Gibbs <gibbs@FreeBSD.org> and Scott Long <scottl@FreeBSD.org> have made more substantial improvements. BUGS
BSD
May 13, 2010 BSD
All times are GMT -4. The time now is 03:19 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy