/boot is not very interesting. Run it on /dev/hda3
Quote:
I tried to execute the following commands (hdparm) to tune the harddrive, but they don't seem to be working on my PC. Please take a look them and guide me further.
Noo! You have SCSI disks!! As you noted in a previous message, /boot is on /dev/sda, which means SCSI. Go into your SCSI Bios setup (during a reboot) and see if you can determine the bus speed and max data rate for the device. Examples will be: 20, 40, 80, 160, 320 Mbits / s. Also see if you can identify the hard drive. If the SCSI BIOS doesn't help you, you can use dmesg or cat /proc/scsi/scsi
Quote:
NOOOOO NEVER DO THAT (unless you know what you're really doing). Did you not see the "SEVERE damage" part of the message?
sorry wrong forum..i dont know how to delete this or how to move it to HP UX section...
I tested SAX XML parsing using xerces(http://xerces.apache.org/xerces-j/). I tested on Windows XP and HP-UX . I found that parsing time on HP is 5 times that on Windows. My server startup reads a lot of XML... (1 Reply)
Is it possible to build Boost 1.35 using Sun Studio 10?
I can build Boost 1.35 using Sun Studio 11 successful. However, i'm unable to build it using Sun Studio 10 using the exact method.
I really apprecaite if any expert can help on this.
Thanks, (2 Replies)
Hi All
I am working unders Sun Solaris and I am not
"/opt/boost/boost/thread/detail/thread.hpp", line 344: Error: boost::thread::thread(boost::thread&) is not accessible from boost::move(boost::detail::thread_move_t<boost::thread>).
Do you know if there are other solutions other than... (2 Replies)
I always had helpful replies from this site when ever I have posted a question.
My current problem is that I am trying to read a book titled "Solaris(TM) Performance and Tools: DTrace and MDB Techniques for Solaris 10" and I am frustrated because inspite of the fact that it is a good book I just... (2 Replies)
Hi,
Based on the following example in the Boost C++ website:
www. boost.org/doc/libs/1_47_0/doc/html/boost_asio/example/echo/async_tcp_echo_server.cpp]doc/html/boost_asio/example/echo/async_tcp_echo_server.cpp
I tried to create a similar TCP server that waits to accept a client connection... (0 Replies)
Hello all,
I am trying to "make" a database system, VDB (Veritas Data Base), and when I run "make" I receive the following error:
VDBException.h:19: error: expected `)' before '*' token
VDBException.h:20: error: expected `)' before '*' token
VDBException.h:43: error: expected `)' before '*'... (4 Replies)
Hi,
I just started using CMake and the Boost Libraries. In this progress I encountered some problems.
One of these problems is combining Boost unit tests with cmake. I don't know how to set the whole project up. I tried to set up a simple test project. This contains a main.cpp a comp.cpp and the... (0 Replies)
I am trying to use the split provided by boost.
I have a string and want to split on "/".
string value = "trig/4";
Have no idea how to compile and link it. I have extracted boost in
/chrisd/tomso-12.04/source/library/boost_1_52_0 In my program /raytrac.cc I have put
... (5 Replies)
Discussion started by: kristinu
5 Replies
LEARN ABOUT X11R4
fsck.minix
FSCK.MINIX(8) System Administration FSCK.MINIX(8)NAME
fsck.minix - check consistency of Minix filesystem
SYNOPSIS
fsck.minix [options] device
DESCRIPTION
fsck.minix performs a consistency check for the Linux MINIX filesystem.
The program assumes the filesystem is quiescent. fsck.minix should not be used on a mounted device unless you can be sure nobody is writ-
ing to it. Remember that the kernel can write to device when it searches for files.
The device name will usually have the following form:
/dev/hda[1-63] IDE disk 1
/dev/hdb[1-63] IDE disk 2
/dev/sda[1-15] SCSI disk 1
/dev/sdb[1-15] SCSI disk 2
If the filesystem was changed, i.e., repaired, then fsck.minix will print "FILE SYSTEM HAS CHANGED" and will sync(2) three times before
exiting. There is no need to reboot after check.
WARNING
fsck.minix should not be used on a mounted filesystem. Using fsck.minix on a mounted filesystem is very dangerous, due to the possibility
that deleted files are still in use, and can seriously damage a perfectly good filesystem! If you absolutely have to run fsck.minix on a
mounted filesystem, such as the root filesystem, make sure nothing is writing to the disk, and that no files are "zombies" waiting for
deletion.
OPTIONS -l, --list
List all filenames.
-r, --repair
Perform interactive repairs.
-a, --auto
Perform automatic repairs. This option implies --repair and serves to answer all of the questions asked with the default. Note
that this can be extremely dangerous in the case of extensive filesystem damage.
-v, --verbose
Be verbose.
-s, --super
Output super-block information.
-m, --uncleared
Activate MINIX-like "mode not cleared" warnings.
-f, --force
Force a filesystem check even if the filesystem was marked as valid. Marking is done by the kernel when the filesystem is
unmounted.
-V, --version
Display version information and exit.
-h, --help
Display help text and exit.
DIAGNOSTICS
There are numerous diagnostic messages. The ones mentioned here are the most commonly seen in normal usage.
If the device does not exist, fsck.minix will print "unable to read super block". If the device exists, but is not a MINIX filesystem,
fsck.minix will print "bad magic number in super-block".
EXIT CODES
The exit code returned by fsck.minix is the sum of the following:
0 No errors
3 Filesystem errors corrected, system should be rebooted if filesystem was mounted
4 Filesystem errors left uncorrected
7 Combination of exit codes 3 and 4
8 Operational error
16 Usage or syntax error
AUTHORS
Linus Torvalds <torvalds@cs.helsinki.fi>
Error code values by Rik Faith <faith@cs.unc.edu>
Added support for filesystem valid flag: Dr. Wettstein <greg%wind.uucp@plains.nodak.edu>.
Check to prevent fsck of mounted filesystem added by Daniel Quinlan <quinlan@yggdrasil.com>.
Minix v2 fs support by Andreas Schwab <schwab@issan.informatik.uni-dortmund.de>, updated by Nicolai Langfeldt <janl@math.uio.no>.
Portability patch by Russell King <rmk@ecs.soton.ac.uk>.
SEE ALSO fsck(8), fsck.ext2(8), mkfs(8), mkfs.ext2(8), mkfs.minix(8), reboot(8)AVAILABILITY
The fsck.minix command is part of the util-linux package and is available from Linux Kernel Archive <https://www.kernel.org/pub/linux/utils
/util-linux/>.
util-linux June 2015 FSCK.MINIX(8)