11-10-2008
thanx reborg!
I do next movement:
Correct /etc/hosts
Quote:
# Internet host table
#
::1 localhost
127.0.0.1 localhost
172.17.0.15 www2 www2.domain.ru loghost
172.17.0.5 mailhost.domain.ru
and restart sendmail:
Quote:
bash-3.00# svcadm disable sendmail
bash-3.00# svcadm enable sendmail
message was received but only after 10 minute!
syslog:
Quote:
Nov 10 17:52:04 www2 sendmail[1111]: [ID 801593 mail.info] mAAEq2Os001111: localhost [127.0.0.1] did not issue MAIL/EXPN/VRFY/ETRN during connection to NoMTA4
why does it slowly?
Last edited by sotich82; 11-10-2008 at 10:57 AM..
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have a primary/slave Bind 9 setup running on a Solaris 10 platform. Everything is hunky dorey, except for when I make a zone file change and up the serial the file that is transferred to the slave looses all its comments, and the entries are place in alphabetical order.
I administer many... (1 Reply)
Discussion started by: fulhamfcboy
1 Replies
2. Solaris
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
Discussion started by: vvpotugunta
2 Replies
3. Solaris
I have two physical servers, with zones that mount local storage.
We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point).
It failed to mount on every boot because the directory existed in the zone.
I... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies
4. Solaris
can some one help me out as it is showing 2 different time zones in global zone and nonglobal zone .In global zone it is showing in GMT while in nonglobal zone i it showing as PDT.
System in running with solaris 10 (3 Replies)
Discussion started by: ravijanjanam12
3 Replies
5. Solaris
So this is Solaris 11.1. I have a Global zone that has several non-global zones running in it. I want to change the capped-memory.physical resources setting in ALL the zone configs of the running zones.
if I were to do this manually here's what I would do:
zonecfg -z zone1
select... (2 Replies)
Discussion started by: os2mac
2 Replies
6. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
7. Solaris
TLDR; non-global-zone has same configuration files (sendmail.cf) as global-zone but still unable to send mail out using mailx
I have a S11.3 system that has a non-global-zone which uses the exact same sendmail.cf configurations as the global but, unable to send mail out from it.
Apparently... (2 Replies)
Discussion started by: samthewildone
2 Replies
8. Solaris
This is isolated to just 1 non-global zone out of many zones managed
This is a Solaris 11 system on SPARC
This is NOT a branded zone
syslogd is active
This came to our attention when one of our scripts didn't run over the weekend prompting us to check our messages logging in... (6 Replies)
Discussion started by: samthewildone
6 Replies
9. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT DEBIAN
sendmailconfig
SENDMAILCONFIG(8) System Manager's Manual SENDMAILCONFIG(8)
NAME
sendmailconfig - configure sendmail for Debian systems
SYNOPSIS
sendmailconfig [--no-reload]
DESCRIPTION
sendmailconfig is used to simplify the configuration of sendmail(8) for use on Debian systems.
In the simplest case, you may run this program to (re)configure sendmail for your Debian system at any time. It will modify the file
/etc/mail/sendmail.mc in order to create a working sendmail configuration which will be written to the file /etc/mail/sendmail.cf.
For advanced configurations, you can modify the sendmail.mc file before generating sendmail.cf. Future invokations of sendmailconfig will
preserve these changes provided they are made at the end of the file.
Normally sendmailconfig will ask if you want to reload sendmail after making changes to its configuration. The --no-reload option will
avoid this question.
FILES
/etc/mail/sendmail.mc
sendmail m4 input to generate sendmail.cf
/etc/mail/sendmail.cf
actual sendmail configuration file
/etc/mail/sendmail.cw
names for which we will accept mail in the standard configuration
/etc/mail/sendmail.ct
names of trusted users in the standard configuration
SEE ALSO
sendmail(8)
AUTHOR
Robert Leslie <rob@mars.org>
21-Jan-1997 SENDMAILCONFIG(8)