11-10-2008
thanx reborg!
I do next movement:
Correct /etc/hosts
Quote:
# Internet host table
#
::1 localhost
127.0.0.1 localhost
172.17.0.15 www2 www2.domain.ru loghost
172.17.0.5 mailhost.domain.ru
and restart sendmail:
Quote:
bash-3.00# svcadm disable sendmail
bash-3.00# svcadm enable sendmail
message was received but only after 10 minute!
syslog:
Quote:
Nov 10 17:52:04 www2 sendmail[1111]: [ID 801593 mail.info] mAAEq2Os001111: localhost [127.0.0.1] did not issue MAIL/EXPN/VRFY/ETRN during connection to NoMTA4
why does it slowly?
Last edited by sotich82; 11-10-2008 at 10:57 AM..
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have a primary/slave Bind 9 setup running on a Solaris 10 platform. Everything is hunky dorey, except for when I make a zone file change and up the serial the file that is transferred to the slave looses all its comments, and the entries are place in alphabetical order.
I administer many... (1 Reply)
Discussion started by: fulhamfcboy
1 Replies
2. Solaris
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
Discussion started by: vvpotugunta
2 Replies
3. Solaris
I have two physical servers, with zones that mount local storage.
We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point).
It failed to mount on every boot because the directory existed in the zone.
I... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies
4. Solaris
can some one help me out as it is showing 2 different time zones in global zone and nonglobal zone .In global zone it is showing in GMT while in nonglobal zone i it showing as PDT.
System in running with solaris 10 (3 Replies)
Discussion started by: ravijanjanam12
3 Replies
5. Solaris
So this is Solaris 11.1. I have a Global zone that has several non-global zones running in it. I want to change the capped-memory.physical resources setting in ALL the zone configs of the running zones.
if I were to do this manually here's what I would do:
zonecfg -z zone1
select... (2 Replies)
Discussion started by: os2mac
2 Replies
6. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
7. Solaris
TLDR; non-global-zone has same configuration files (sendmail.cf) as global-zone but still unable to send mail out using mailx
I have a S11.3 system that has a non-global-zone which uses the exact same sendmail.cf configurations as the global but, unable to send mail out from it.
Apparently... (2 Replies)
Discussion started by: samthewildone
2 Replies
8. Solaris
This is isolated to just 1 non-global zone out of many zones managed
This is a Solaris 11 system on SPARC
This is NOT a branded zone
syslogd is active
This came to our attention when one of our scripts didn't run over the weekend prompting us to check our messages logging in... (6 Replies)
Discussion started by: samthewildone
6 Replies
9. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT OSF1
mailstats
mailstats(8) System Manager's Manual mailstats(8)
NAME
mailstats - Displays statistics about mail traffic
SYNOPSIS
mailstats [-o] [-C cffile [-f stfile]
FLAGS
Do not display the name of the mailer in the output. Use cffile as the name of the sendmail "cf" file instead of /var/adm/sendmail/send-
mail.cf. Use stfile as the input statistics file instead of /var/adm/sendmail/sendmail.st.
DESCRIPTION
The mailstats command reads the information in the /var/adm/sendmail/sendmail.st file (or in the file specified with the -f flag), formats
it, and writes it to standard output. Note also that you can change the location of the sendmail.st file by editing its pathname in the
sendmail.cf file.
EXAMPLES
The format of the information is shown in the following example, in which the first field (M) contains a number that indicates the position
of that mailer in the sendmail.cf file, starting at 0 (zero). For example, the first mailer in the sendmail.cf file corresponds to the
number 0 in the mailstats display, the second mailer corresponds to the number 1, and so on. Statistics from Thu Feb 17 11:20:01 2000 M
msgsfr bytes_from msgsto bytes_to msgsrej msgsdis Mailer 1 50 77K 1 3K 0 0 local 6
43 59K 58 99K 0 0 smtp ============================================================ T 93
136K 59 102K 0 0 The fields in the report have the following meanings: Indicates the position of the mailer in
the sendmail.cf file. Indicates the number of messages received by the local machine from the indicated mailer. Indicates the number of
bytes in the messages received by the local machine from the indicated mailer. Indicates the number of messages sent from the local
machine using the indicated mailer. Indicates the number of bytes in the messages sent from the local machine using the indicated mailer.
Indicates the number of rejected messages. Indicates the number of discarded messages. Indicates the name of the mailer.
If sendmail transmits mail directly to a file, such as the dead.letter file or an alias target, the message and byte counts are credited to
the prog mailer, as defined in the sendmail.cf file. However, mailstats will still default to var/adm/sendmail/sendmail.st.
FILES
Specifies the command path Contains system statistics Contains configuration information for sendmail
RELATED INFORMATION
Commands: sendmail(8) delim off
mailstats(8)