Hi,
I have a primary/slave Bind 9 setup running on a Solaris 10 platform. Everything is hunky dorey, except for when I make a zone file change and up the serial the file that is transferred to the slave looses all its comments, and the entries are place in alphabetical order.
I administer many... (1 Reply)
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
I have two physical servers, with zones that mount local storage.
We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point).
It failed to mount on every boot because the directory existed in the zone.
I... (6 Replies)
can some one help me out as it is showing 2 different time zones in global zone and nonglobal zone .In global zone it is showing in GMT while in nonglobal zone i it showing as PDT.
System in running with solaris 10 (3 Replies)
So this is Solaris 11.1. I have a Global zone that has several non-global zones running in it. I want to change the capped-memory.physical resources setting in ALL the zone configs of the running zones.
if I were to do this manually here's what I would do:
zonecfg -z zone1
select... (2 Replies)
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
TLDR; non-global-zone has same configuration files (sendmail.cf) as global-zone but still unable to send mail out using mailx
I have a S11.3 system that has a non-global-zone which uses the exact same sendmail.cf configurations as the global but, unable to send mail out from it.
Apparently... (2 Replies)
This is isolated to just 1 non-global zone out of many zones managed
This is a Solaris 11 system on SPARC
This is NOT a branded zone
syslogd is active
This came to our attention when one of our scripts didn't run over the weekend prompting us to check our messages logging in... (6 Replies)
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT MINIX
resolvxc
RESOLV.CONF(5) File Formats Manual RESOLV.CONF(5)NAME
resolv.conf - Domain Name System resolver configuration
SYNOPSIS
/etc/resolv.conf
DESCRIPTION
The /etc/resolv.conf is used to configure how the host will use the Domain Name System to resolve hostnames to IP addresses. It may con-
tain these two lines:
nameserver IP-address
domain domain-name
The nameserver entry tells the IP address of the host to use for DNS queries. If it is set to 127.0.0.1 (which is the default) then the
local name daemon is used that may use the /etc/hosts database to translate host names. You normally only need a nameserver entry if the
name server is at the other side of a router. The default nonamed name server can't look beyond the local network.
The domain entry tells the default domain to use for unqualified hostnames. This entry is usually not given in which case the domain of
the local host is used.
The long version of this story can be found in resolver(5).
FILES
/etc/resolv.conf DNS resolver configuration file.
SEE ALSO resolver(5), hosts(5), nonamed(8), boot(8).
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
RESOLV.CONF(5)