Sponsored Content
Top Forums Shell Programming and Scripting network and broadcast address Post 302256290 by scofiled83 on Sunday 9th of November 2008 07:42:20 AM
Old 11-09-2008
thanks for the answer, Could u explain a little bit more, how did u come up to that solution
 

10 More Discussions You Might Find Interesting

1. IP Networking

broadcast address

What is the significance of the broadcast address? (1 Reply)
Discussion started by: 98_1LE
1 Replies

2. UNIX for Dummies Questions & Answers

network address and broadcast address?

say I have a IP address which is 10.0.0.12, and subnet mask is 255.255.255.240, what is the network address and what is the broadcast address which host lives on? And could you explain how to get the answer? thanx in advance! (7 Replies)
Discussion started by: pnxi
7 Replies

3. Solaris

bge card and broadcast address

I have a bge1 card and a bge0 card, i want the broadcast addresses to match, ifconfig shows this lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 ... (1 Reply)
Discussion started by: csaunders
1 Replies

4. AIX

NETWORK IP ADDRESS on HACMP

Hi, I try to understand how to configure my ethernet network in a hacmp cluster. I have 2 nodes, 3 lan port on each node, and 1 service ip to cluster. I don't have any serial o iscsi heartbeat. Do you suggest me a possibile ip address configuration? I've many error whene I verify it from hacmp... (3 Replies)
Discussion started by: hacmp
3 Replies

5. IP Networking

Obtaining IP address from both my network interface

HI folks, I am developing a software which one of the module is to interchange the ip address of another active network interface's when making a socket connection. I would like to know whether there is any function call that would enable me to retrieve the ip address that is obtained by a... (2 Replies)
Discussion started by: citiz3n
2 Replies

6. Solaris

ifconfig - making netmask & broadcast address permanent?

hi, I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address. I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated. before reboot: eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies

7. Programming

How to broadcast a message across the network using Socket programming in C??

My problem definition is ,I have to send a message from one node in a network and it has to be broadcasted to all other nodes in the network.The program what I have given below will be running in all the nodes in the network.The same program should be capable of sending(broadcasting) and receiving.... (1 Reply)
Discussion started by: vigneshinbox
1 Replies

8. UNIX for Dummies Questions & Answers

fake network address....

Good morning! Why would having a fake network device be useful? Thanks in advance Bigben (0 Replies)
Discussion started by: bigben1220
0 Replies

9. Shell Programming and Scripting

Shell script to give broadcast and network address

Hello, I am running a post script in autoyast where I am trying to set the broadcast and network address. I have the ip address and netmask already (reading from a file).. I saw the post from fpmurphy but it is using ksh which isn't an option in autoyast. Thanks in advance! (3 Replies)
Discussion started by: bloodclot
3 Replies

10. IP Networking

Network address translation

How would one approach the problem of determining the NAT tables of a router without knowing the userid and password. The only password holder died. I know the internal ip address of the router is 192.168.2.1, and also ports 80 or 8080 and 3389 are open. (5 Replies)
Discussion started by: jgt
5 Replies
diction(1)						      General Commands Manual							diction(1)

NAME
diction, explain, suggest - Prints wordy sentences and looks them up in an interactive thesaurus. SYNOPSIS
diction [-fpattern_file] [-k] [-ma] [-me] [-ml] [-ms] [-n] [file...] explain suggest The diction command finds all sentences in an English language document that contain phrases from a database of bad or wordy diction. The explain command is an interactive thesaurus for the English language phrases found by the diction command and only for those phrases. The diction command reads from standard in if no file operand is provided. The suggest command is a synonym for explain. OPTIONS
Names a user-created pattern file to be used in addition to the default file. Passes the -k option to the deroff command. The -k option keeps blocks of text specified nroff by requests or macros; for example, the request. Passes the -ma option to deroff. The -ma option interprets nroff man macros only. Overrides the default nroff -ms macro package. Causes deroff to skip lists; should be used if a docu- ment contains many lists of nonsentences. Overrides the default nroff -ms macro package. Suppresses use of the default file (used with -f). Only the user-created pattern file is used. DESCRIPTION
Each phrase found by the diction command is enclosed in [ ] (brackets). Because diction runs deroff before looking at the text, include formatting header files as part of the input. Before using the explain command, use the diction command to obtain a list of poorly worded phrases. When you use the explain command, the system prompts you for a phrase and responds with a grammatically acceptable alternative. You can continue typing phrases, or you can exit by pressing the End-of-File key sequence. The explain command can also take input redirected from a file. No other command line arguments are valid. NOTES
Use of nonstandard formatting macros may cause incorrect sentence breaks. In particular, diction does not understand -me. FILES
Default pattern file. Thesaurus used by the explain command. SEE ALSO
Commands: deroff(1), nroff(1) diction(1)
All times are GMT -4. The time now is 07:14 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy