Sponsored Content
Full Discussion: Cause of NIC changes ...?
Operating Systems Solaris Cause of NIC changes ...? Post 302255307 by DukeNuke2 on Thursday 6th of November 2008 07:34:02 AM
Old 11-06-2008
this is no problem. the pci bus is scanned before the internel nics are scanned. so they will become net0 and so on. if you like to have the internal nics to be net0... you have to pull out the additional cards, install the system and then insert the cards again.
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

nic configuration

Hi, what are the basic steps/command to configure a new nic (2nd) on Solaris 9? :eek: 10x N. (4 Replies)
Discussion started by: nadav
4 Replies

2. SCO

Need Help installing NIC

Hi guys, I am a newbie in SCO UNIX, and I am having problem in installing a NIC for my machine: My machine: UnixWare scou 5 7.1.4 i386 x86at SCO UNIX_SVR5 My NIC is dLink DFE-538TX, I got the driver from: http://support.dlink.ca/ProductView.asp?ProductModel=DFE-538TX The driver... (1 Reply)
Discussion started by: Voldi
1 Replies

3. Shell Programming and Scripting

NIC address

how can I know the Network Interface Card physical address? (4 Replies)
Discussion started by: nokia1100
4 Replies

4. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

5. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

6. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

7. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

8. HP-UX

Configure Second NIC on HP UX?

Hello, I need to configure a second NIC on my HP UX, B.11.31 U ia64 ...if it is helpful. I see a good thread to start on: Configuring NIC https://www.unix.com/hp-ux/15589-configuring-nic.html I have started reading the man pages listed. Without having to know every last detail is there... (3 Replies)
Discussion started by: KmJohnson
3 Replies

9. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
OCF_HEARTBEAT_SENDAR(7) 					OCF resource agents					   OCF_HEARTBEAT_SENDAR(7)

NAME
ocf_heartbeat_SendArp - Broadcasts unsolicited ARP announcements SYNOPSIS
SendArp [start | stop | monitor | meta-data | validate-all] DESCRIPTION
This RA can be used _instead_ of the IPaddr2 or IPaddr RA to send gratuitous ARP for an IP address on a given interface, without adding the address to that interface. For example, if for some resaon you wanted to send gratuitous ARP for addresses managed by IPaddr2 or IPaddr on an additional interface. SUPPORTED PARAMETERS
ip The IP address for sending ARP packet. (required, string, no default) nic The NIC for sending ARP packet. (required, string, no default) SUPPORTED ACTIONS
This resource agent supports the following actions (operations): start Starts the resource. Suggested minimum timeout: 20s. stop Stops the resource. Suggested minimum timeout: 20s. monitor Performs a detailed status check. Suggested minimum timeout: 20. Suggested interval: 10. meta-data Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5. validate-all Performs a validation of the resource configuration. Suggested minimum timeout: 20s. EXAMPLE
The following is an example configuration for a SendArp resource using the crm(8) shell: primitive p_SendArp ocf:heartbeat:SendArp params ip=string nic=string op monitor depth="0" timeout="20" interval="10" SEE ALSO
http://www.linux-ha.org/wiki/SendArp_(resource_agent) AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors) resource-agents UNKNOWN 03/09/2014 OCF_HEARTBEAT_SENDAR(7)
All times are GMT -4. The time now is 11:19 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy