11-05-2008
External NIC cards not pinging with each other in RHEL 5.1
We have a setup of two nodes which has two NIC cards in each. One is built in and another is D-Link (external NIC card). We are unable to ping to the external NIC cards in both. Eg: Node A has two IPs 192.168.1.10 (eth0) and 192.168.2.10 (eth1) and Node B has two IPs 192.168.1.20 (eth0) and 192.168.2.20 (eth1). These setup has two switches, where 192.168.1.10 and 192.168.1.20 is connected to Switch A, 192.168.2.10 and 192.168.2.20 is connected to Switch B.
The problem here is from 192.168.1.10 is able to ping 192.168.1.20 but not to 192.168.2.20 same with the Node B 192.168.1.20 is able to ping 192.168.1.10 but not 192.168.2.10. when all are placed in same network then all IPs are pinging with each other.
All Linux gurus please help me .. pls treat this request as high prioprity!!
10 More Discussions You Might Find Interesting
1. Solaris
I need to add a PCI NIC to a sunblade 100 running solaris 8. Im new to this and was hoping someone could give me some card names and models which will work for this system and has a driver for this sparc system.
thanks (3 Replies)
Discussion started by: meyersp
3 Replies
2. IP Networking
Hi;
I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now... (2 Replies)
Discussion started by: texaspanama
2 Replies
3. High Performance Computing
Hello
I have 2 machines with 3 NIC cards.
When I setup veritas, I receive this message:
e1000g1 has an IP address configured on it. It could be a public NIC on ken.
Are you sure you want to use e1000g1 for the first private heartbeat link?
As if e1000g1 should not have an IP address.... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies
4. HP-UX
I am running HP_UX 11.23 with 4 NIC cards (this is our TSM server)
I have 4 subnets we are backing across. trying to keep traffic on their subnets. I only have one route statment should I add more.
route add net 123.99.8.0 netmask 255.255.255.0 123.99.8.254
route add net 123.99.67.0 netmask... (2 Replies)
Discussion started by: myork
2 Replies
5. HP-UX
Hello,
I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches.
On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular... (1 Reply)
Discussion started by: ldaliosmane
1 Replies
6. IP Networking
Hi,
What is the best reference that gives in detail on nic cards configuration , assigning multiple ip addresses to a single interface, netlink library etc and all basic stuff at this level..?
Thanks (2 Replies)
Discussion started by: Gopi Krishna P
2 Replies
7. Red Hat
Ok, Im trying to get NFS working on my RHEL 5 box, apparently i can use the box as a client, but not as a server. If it helps i cant ssh into the box (server), but as a client ssh works fine. Ive configured
server:
/etc/hosts.allow:
all : all
all :all@all
setup my /etc/exports file... (4 Replies)
Discussion started by: drs.grid
4 Replies
8. Ubuntu
I found an old post that talks about 2 nice cards and it is driven by the IP address .... but I didn't understand it because the 2 people skipped information for me the newbie..
Can someone help me... I have the proxy server setup and I believe I have enabled the 2nd nic card, I just need one... (1 Reply)
Discussion started by: trilju2005
1 Replies
9. Ubuntu
I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table?
I don't know how to do this.:confused: (9 Replies)
Discussion started by: trilju2005
9 Replies
10. Red Hat
I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch.
The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Discussion started by: tjcooper
0 Replies
LEARN ABOUT DEBIAN
oidentd_masq.conf
oidentd_masq.conf(5) File Formats Manual oidentd_masq.conf(5)
NAME
oidentd_masq.conf - oidentd IP masquerading/NAT configuration file.
DESCRIPTION
If you are using IP masquerading or NAT, oidentd can optionally return a username for connections from other machines. Support for this is
specified by calling oidentd with the -m (or --masq) flag and by creating an /etc/oidentd_masq.conf file.
oidentd can also forward requests for an IP masqueraded connection to the machine from which connection originates by way of the -f option.
This will only work if the host to which the connection is forwarded is running oidentd with the -P (proxy) flag, or if the host's ident
daemon will return a valid reply regardless of the input supplied by and the address of the host requesting the info (some ident daemons
for windows do this, maybe others).
FORMAT
<IP Address|Hostname>[/<Mask>] <Ident Response> <System Type>
The first field contains the IP address or the hostname of a machine that IP masquerades through the machine on which oidentd runs. The
mask parameter can be either a network mask or a mask in CIDR notation. A mask of 24 is equivalent to 255.255.255.0, a mask of 16 is
equivalent to 255.255.0.0, etc.
The second field specifies the reply that oidentd will return for lookups to the host matching the IP address specified in the first param-
eter.
The third field specifies the operating system the machine matching the first parameter is running.
EXAMPLES
<Host>[/<Mask>] <Ident Response> <System Type>
192.168.1.1 someone UNIX
192.168.1.2 noone WINDOWS
192.168.1.1/32 user1 UNIX
192.168.1.0/24 user3 UNIX
192.168.0.0/16 user4 UNIX
somehost user5 UNIX
192.168.1.0/255.255.255.0 user6 UNIX
AUTHOR
Ryan McCabe <ryan@numb.org>
http://dev.ojnk.net
SEE ALSO
oidentd(8) oidentd.conf(5)
version 2.0.8 13 Jul 2003 oidentd_masq.conf(5)