Sponsored Content
Full Discussion: openSuse 10.3 , Emulex HBA
Top Forums UNIX for Advanced & Expert Users openSuse 10.3 , Emulex HBA Post 302254262 by nux007 on Tuesday 4th of November 2008 03:37:00 AM
Old 11-04-2008
Question openSuse 10.3 , Emulex HBA

hello, i have a dell Poweredge 2950 ( Server ) and an IBM storage device DS 3000 family ( Storage ) . I am supposed to link the IBM storage device to the Dell Poweredge via "Emulex 4Gb Fibre Channel Host Bus Adapter".

I have put the addapter card in my server and connected it to the storage. When i lspci on my server i get this output :

0c:00.0 Fibre Channel: Emulex Corporation Zephyr-X LightPulse Fibre Channel Host Adapter (rev 02)

So that makes me belive that Suse knows about the adapter card. Problem is i have not been able to make the dell server "see" the storage device via the adapter card ( which is connected using optic fibers ). Another problem is that documantation is kind of scarce and i haven't used anything like this before. Can anyone help me figure this out ? What do i need to do in order to make this work ?
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

HBA compatible on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server.

Hi there, does anybody knows/info on compatiblity on Emulex Lightpulse 9000 with IBM 8840 PKU X346 server. Regards. (0 Replies)
Discussion started by: gagasan_makmur
0 Replies

2. Solaris

emulex card on solaris 9

Hello, I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9). Who have already done this and can give me the procedure to follow ? driver to install multipath etc... Thanks in advance Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies

3. UNIX for Advanced & Expert Users

Solaris 10 x86_64 - Emulex Fibrechannel drivers

Hello! I'm having problems to install Emulex fibrechannel card drivers to a HP DL580 G5 running Solaris 10 x86_64. Any of you guys had this problem or knows the answer? =) cfgadm gives me the following info, which seems to say that it is ok? But the card has'nt logged into the switch... (0 Replies)
Discussion started by: Esaia
0 Replies

4. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies

5. Solaris

What is an HBA..?

Helo experts What is an HBA? How can i know about that on any server? Thanx in advance... (7 Replies)
Discussion started by: younus_syed
7 Replies

6. Solaris

Connect Solaris 10 to NetApp filer using Emulex single port HBAs.

Hi, I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings. Do I need... (6 Replies)
Discussion started by: gwhelan
6 Replies

7. AIX

Need HBA card driver

Hi All, SUN emulex HBA card has been installed on P520 box. When i run the cfgmgr i am getting the following message. lpar2#cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies

8. Filesystems, Disks and Memory

HBA performance

Hope I'm in the right place. I'm in the process of zoning HBA's to my new library environment. Is there a "rule of thumb" for the number of physical tape drives that you zone to an HBA? I don't want to run the risk of overloading an HBA. Any information would be greatly appreciated. Thanks. (2 Replies)
Discussion started by: jwholey
2 Replies

9. Solaris

Offline HBA.

Hi, I have a HBA that is currently offline for some unknown reason. The device shows up in the prtdiag -v stating it is okay. How can I bring this back online? It was working okay until recently. It is currently connected to the SAN. Details below. # fcinfo hba-port HBA Port WWN:... (7 Replies)
Discussion started by: sparcman
7 Replies

10. Solaris

How to enable hba port of a two port hba card

Hi, i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port. ---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ---------- please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
hbaapi(3C)																hbaapi(3C)

NAME
hbaapi - Fibre Channel Storage Network Industry Association Host Bus Adapter Application Programming Interface (FC SNIA HBA API) DESCRIPTION
The Common HBA API provides a consistent HBA standard interface for accessing information in a Fibre Channel Storage Area Network (SAN) that would be implemented across vendors as a standard 'C' API supported by vendor specific library instances. This API library is thread-safe, but threads should not be cancelled when execution is in the API. The following functions are available in the API for managing a Fibre Channel HBA. This API would be exposed to upper level applications to control SAN functionality. Please refer to for details on structures used. 01. 02. 03. 04. 05. 06. 07. 08. 09. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. FCP Information Functions require that the applications calling them have an effective user id as that of the root user (euid = 0). 20. 21. 22. SCSI Information Functions require that the applications calling them have an effective user id as that of the root user (euid = 0). 23. 24. FILES
Contains the related data structures and definitions as in AUTHOR
These APIs were developed by Hewlett-Packard Company. SEE ALSO
HBA_GetVersion(3C), HBA_LoadLibrary(3C), HBA_FreeLibrary(3C), HBA_GetNumberOfAdapters(3C), HBA_GetAdapterName(3C), HBA_OpenAdapter(3C), HBA_CloseAdapter(3C), HBA_GetAdapterAttributes(3C), HBA_GetAdapterPortAttributes(3C), HBA_GetPortStatistics(3C), HBA_GetDiscoveredPortAt- tributes(3C), HBA_GetPortAttributesByWWN(3C), HBA_SendCTPassThru(3C), HBA_GetEventBuffer(3C), HBA_SetRNIDMgmtInfo(3C), HBA_GetRNIDMgmt- Info(3C), HBA_SendRNID(3C), HBA_GetFcpTargetMapping(3C), HBA_GetFcpPersistentBinding(3C), HBA_SendScsiInquiry(3C), HBA_SendReportLUNs(3C), HBA_SendReadCapacity(3C), HBA_RefreshInformation(3C), HBA_ResetStatistics(3C). hbaapi(3C)
All times are GMT -4. The time now is 11:27 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy