[...] When I try to add a client to the NIM environment (from client side), I get the following errors:
1) 0042-376 niminit: This command cannot be executed on a NIM master unless the "is_alternate" attribute is specified.
(I never configured this client as a NIM master)
[...]
Perhaps the criteria for being identified as a NIM master is not a NIM master setup but the mere existence of the corresponding fileset.... Assuming that the master fileset is bos.sysmgt.nim.master (writing from memory) try this as root:
$ errpt | more
IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION
3074FEB7 0802050205 T H fscsi1 ADAPTER ERROR
B8113DD1 0802050205 T H fcs1 LINK ERROR
B8113DD1 0802050205 T H fcs1 LINK ERROR
3074FEB7 0802050205 T H fscsi0 ADAPTER ERROR
B8113DD1 ... (0 Replies)
$ errpt | more
IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION
3074FEB7 0802050205 T H fscsi1 ADAPTER ERROR
B8113DD1 0802050205 T H fcs1 LINK ERROR
B8113DD1 0802050205 T H fcs1 LINK ERROR
3074FEB7 0802050205 T H fscsi0 ADAPTER ERROR
B8113DD1 ... (2 Replies)
I try to migrate a NIM server from one server to another.
I try to do a mksysb on NIM server
restore the NIM server's mksysb to a client through NIM installation
shutdown NIM server
start newly installed client as NIM server
Does anyone do this before? who can give me some suggestion? (1 Reply)
Hi all, dummy here.... I have major errors on entering the shell. On login I get:
-bash: dircolors: command not found
-bash: tr: command not found
-bash: fgrep: command not found
-bash: grep: command not found
-bash: grep: command not found
-bash: id: command not found
-bash: [: =: unary... (12 Replies)
Hello everyone
I have two questions.
1.-The NIM and EZNIM are the same.
2.-If I have in one partition NIM installed I need to install EZNIM or I need to unistall NIM and then install EZNIM.
Thanks for your comments. (2 Replies)
Hello everyone
Im trying to backup a nim client from nim master but I got this message
COMMAND STATUS
Command: failed stdout: yes stderr: no
Before command completion, additional instructions may appear below.
0042-001 nim:... (2 Replies)
Hello
I would like to hear your opinions about shell and nimsh
I install the nim master on a server and and client nim on others servers. I backup this clients with the NIM master.
When Im trying to install the clients with the option nimsh (communication protocol) send me an error
... (1 Reply)
Hi.
I change my client's IP and hostname but I forgot to change anything on the master. How can I redefine or modify my client's resource from my master, or with using smit niminit from my client ?
Tks (2 Replies)
Hello, I have an AIX6.1 machine which is a nim client to my nim master which is also AIX6.1 machine. I had some problem to perform an installation on my client using smit nim . i removed /etc/niminfo file in order to do the initialization again but when i run the command niminit -a name=client... (0 Replies)
Friend's,
I was playing around with NIM in my environment & had a quick question in mind which I didn't/couldn't find answer to, which is -- how to find the name of the NIM server sitting on the NIM client?
All leads to the answer would be much appreciated, many thanks!
-- Souvik (2 Replies)
Discussion started by: thisissouvik
2 Replies
LEARN ABOUT ULTRIX
ypsetup
ypsetup(8yp)ypsetup(8yp)Name
ypsetup - set up the yellow pages (YP) environment
Syntax
/usr/etc/ypsetup
Description
A local area network must be set up on your system before you can set up YP. You must know your system's default YP domain name and
whether your system will be a master server, slave server, or client. If your system is to be the master server for your YP domain, be
sure no other master has been established and be sure the files to be distributed are in the directory Note that the files to be distrib-
uted should be modified from the original files by removing the root entry in the file.
If your system is not to be the master server, be sure a master already exists for your YP domain. Once you know this information, run
with the system in multiuser mode and answer its questions.
Once YP is installed on a machine, it cannot be used until the file is modified to contain YP entries on the desired database lines. The
command reminds a user to run or edit the file manually.
Files
Files that Start the YP daemons
Clock daemon database file
Commands pertinent to a specific system
Default YP Map Files
Group database
Host name database
Sendmail alias database
Network group aliases
Network name database
Password file
Protocol name database
Rpc name database
Service name database
See Alsodomainname(1yp), ypwhich(1yp), svc.conf(5), svcsetup(8), yppasswdd(8yp), ypserv(8yp), ypxfr(8yp)
Guide to the Yellow Pages Service
ypsetup(8yp)