yea, I'm a really dummie, I have been using Knoppix for a while on a bootable disk, but wanting to switch to Slackware, is this a good decision? could any of you link me to a slackware downloadable site? thanks
-Jace:D (7 Replies)
I am using awk in my .ksh script but when I am trying to run in windows
its not recognising awk part of the ksh script , even when I changed it to gawk it does not work, this is how my .ksh and .bat files look like.
thanx.
#!/bin/ksh
egrep -v "Rpt 038|PM$|Parameters:|Begin |Date: |End... (1 Reply)
If I cat a file
And want to go to the first instance of a particular value - what command would I use?
And then from that point where I jumped to search for another value - but only search from that point forward not before the file?
Thanks~ (2 Replies)
Hi all,
I need to create a bash script that reads a txt file on a remote (Windows 2003) server, gets the IP-addresses out of it and then fetches the folders to copy out of another txt file. (all files are auto-generated) The IP addresses that don't have a folder_list file should be ignored. At... (31 Replies)
Ok apologies if this is trivial or doesn't make sense but I am quite new to korn shells;
So I have a .ksh batch file located in a folder of my choosing, I want to run this file in a korn shell.
The problem though is that I want to get VBA code to do this. I have (VBA) code which opens command... (1 Reply)
Hi there,
in near future I have to change my work surrounding from HP UNIX to Windows Vista (great to get rid of old hardware :), but bad to loose UNIX :( ). As I heavily use KSH scripts to do my job, I was wondering, if there is any HowTo available, supporting me in re-writing the scripts to... (4 Replies)
Hi,
can someone point out a solution to my problem below.
Within a shell script TEST.ksh I have to run two commands CmdA & CmdB one after the other as below.
-------------
TEST.ksh
#!/usr/bin/ksh
A
B
-------------
I am running this script from KSH with PID 12345 as below.
... (5 Replies)
Hello everyone. I am new to shell scripting and i am required to create a shell script, the purpose of which i will explain below.
I am on a solaris server btw.
Before delving into the requirements, i will give youse an overview of what is currently in place and its purpose.
... (2 Replies)
Hi, i want the loop to move to 3rd item, when it encounters 2 while runing
for i in 1 2 3 4 5 6
do
if
then
#jump to element 3
else
echo $i
fi
done
o/p
1
3
4
5
6 (4 Replies)
HI I have the following output from an autosys command .
Now I would like to investigate further .i.e
Start Dependent
Job Name Status ... (3 Replies)
Discussion started by: ptappeta
3 Replies
LEARN ABOUT DEBIAN
qmove
qmove(1B) PBS qmove(1B)NAME
qmove - move pbs batch job
SYNOPSIS
qmove destination job_identifier ...
DESCRIPTION
To move a job is to remove the job from the queue in which it resides and instantiate the job in another queue. The qmove command issues a
Move Job batch request to the batch server that currently owns each job specified by job_identifier.
A job in the Running , Transiting , or Exiting state cannot be moved.
OPERANDS
The first operand is the new destinationfor
queue
@server
queue@server
See the PBS ERS section , "Destination Identifiers".
If the destination operand describes only a queue, then qmove will move jobs into the queue of the specified name at the job's current
server.
If the destination operand describes only a batch server, then qmove will move jobs into the default queue at that batch server.
If the destination operand describes both a queue and a batch server, then qmove will move the jobs into the specified queue at the speci-
fied server.
All following operands are job_identifiers which specify the jobs to be moved to the new destination. The qmove command accepts one or
more job_identifier operands of the form:
sequence_number[.server_name][@server]
STANDARD ERROR
The qmove command will write a diagnostic messages to standard error for each error occurrence.
EXIT STATUS
Upon successful processing of all the operands presented to the qmove command, the exit status will be a value of zero.
If the qmove command fails to process any operand, the command exits with a value greater than zero.
SEE ALSO qsub(1B), pbs_movejob(3B)Localqmove(1B)