Problem with Etherchannel Post: 302252471

10 More Discussions You Might Find Interesting

1. AIX

EtherChannel network redundance problem

Problem description: On the condition of EtherChannel function of AIX, when the data exchange between the nodes on the network, there sometimes lost datat packets and cause the application failed. Once we deconfig EtherChannel and use the single adapter configuration, the application works...

2. AIX

AIX / Etherchannel / VLANs

I have 1 AIX server, 4 dual ported fiber attached ethernet cards and 4 VLANS coming in. Is it possible to present those 8 ports as 1 IP address using etherchannel? Thanks.

3. AIX

How to find the active network inteface on etherchannel

I have a server with multiple network interfaces. 2 of these interfaces, lets say en2 and en6 make up an etherchannel interface, which let's say en8. when I run the command lsattr -El ent8 I can see the designated primary and backup interfaces as ent6 and ent2, in the given order. But...

4. BSD

FreeBsd 8.0 : Just for Gurus! Trunk/Etherchannel mode

Hi Buddies! I need to do a new kind of setting in FreeBSD (i'm a newbie using this OS). Interface 1 y 2 in Trunk/Etherchannel mode IP-> xx.xx.xx.xx netmask-> 255.255.255.0 Anybody can help me with a step by step Guide?. THANKS A MILLION!!!

5. AIX

Pb Etherchannel/deconnexion port reseau

Hello, On a partition with AIX 5300-11-01-0944. 1 etherchannel ent9 with aggregation ent3/ent7. # lsdev |grep ent ... ent3 Available 07-01 4-Port 10/100/1000 Base-TX PCI-Express Adapter (14106803) ... ent7 Available 0A-01 4-Port 10/100/1000 Base-TX PCI-Express...

6. AIX

Can EtherChannel be a redundancy config?

I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches. How to make this as a redundancy config? Current is if one physical network adapter down, the seond one will go through the network. but if...

7. AIX

EtherChannel interface ping pelicularity

I have few AIX servers in my data center, which have their EtherChannel configured to have a fat pipe (active/active) and a nagios server to monitor the server uptimes. Nagios server pings every server in the data center and we have pretty much every known unix flavor in this data center. When...

8. AIX

Aggregated Etherchannel

Hi, I have a AIX5.3 P6-520 with 8x1Gb Ethernet ports with possible connections to 2 CISCO 2960 switches. I can create 8023ad Etherchannels which work correctly with the switches (I have set up for LACP passive and a valid channels) But can create 2x 8023ad 4Gb Etherchannels with no backups....

9. AIX

Etherchannel failover testing

Hi Guys, I am trying to test an etherchannel failover and switchback. I did failover from primary to backup adapter, but now I am not able to switch it back to primary. phcxxxxx:/ > entstat -d ent4 | grep Active Active channel: backup adapter ...

10. AIX

PowerVM SEA etherchannel performance ?

Hello, POWER7 machine. 4 x 1Gbit port ethernet adapter is dedicated to vios. 8023ad etherchannel is created using those 4 ports. Etherchannel adapter is shared to lpars using SEA. If I test network performance directly from vios partition (using iperf) I'm geting nice 4Gbit throughput. But if...

LEARN ABOUT REDHAT

vconfig

VCONFIG(8)						      System Manager's Manual							VCONFIG(8)

NAME

       vconfig - VLAN (802.1q) configuration program.

SYNOPSIS

       vconfig [lots of long options]

DESCRIPTION

       The  vconfig program allows you to create and remove vlan-devices on a vlan enabled kernel. Vlan-devices are virtual ethernet devices which
       represents the virtual lans on the physical lan.

OPTIONS

       add [interface-name] [vlan-id]
	      Creates a vlan-device on [interface-name]. The resulting vlan-device will be called according to the nameing convention set.

       rem [vlan-device]
	      Removes the named vlan-device.

       set_flag [vlan-device] 0 | 1
	      When 1, ethernet header reorders are turned on. Dumping the device will appear as a  common  ethernet  device  without  vlans.  When
	      0(default)  however,  ethernet  headers are not reordered, which results in vlan tagged packets when dumping the device. Usually the
	      default gives no problems, but some packet filtering programs might have problems with it.

       set_egress_map [vlan-device] [skb-priority] [vlan-qos]
	      This flags that outbound packets with a particular skb-priority should be tagged with the particular  vlan  priority  vlan-qos.  The
	      default vlan priority is 0.

       set_ingress_map [vlan-device] [skb-priority] [vlan-qos]
	      This  flags  that  inbound  packets  with the particular vlan priority vlan-qos should be queued with a particular skb-priority. The
	      default skb-priority is 0.

       set_name_type VLAN_PLUS_VID | VLAN_PLUS_VID_NO_PAD | DEV_PLUS_VID | DEV_PLUS_VID_NO_PAD
	      Sets the way vlan-device names are created. Use vconfig without arguments to see the different formats.

       NOTES  VLAN will use Broadcom's NICE interface when the network device supports it. This is necessary, since usually the hardware of  these
	      devices  already	removes the vlan tag from the ethernet packet. The set_flag option on vlan-devices created on such a physical net-
	      work device will be ignored.  Dumping the network-device will show only untagged(non-vlan) traffic,  and	dumping  the  vlan-devices
	      will only show traffic intended for that vlan, without the tags.

FILES

       /proc/net/vlan/config
       /proc/net/vlan/[vlan-device]

SEE ALSO

       ip(8), ifconfig(8)

AUTHORS

       This manual page was written by Ard van Breemen <ard@kwaak.net>
       The vlan patch is written by Ben Greear <greearb@candelatech.com>

																	VCONFIG(8)