Sponsored Content
Special Forums IP Networking network segment use vlan, linux vconfig and AT-GS950 Post 302252118 by penyu on Tuesday 28th of October 2008 09:30:32 PM
Old 10-28-2008
Question network segment use vlan, linux vconfig and AT-GS950

Dear all,

I have a Allied Telesyn AT-GS950 16 port switch.
All hosts&router have rtl8139 NICs.
OS : Slackware linux 12.1.
I use a switch with vlan technique to separate my network to some segment.

here my plan:

router eth0 ---> switch port 1
switch port 5 <--- eth0 host A
switch port 6 <--- eth0 host B

in eth0 of router, I make two vlan :
Code:
# modprobe 8021q
# ifconfig eth0 0.0.0.0 up
# vconfig add eth0 5
# ifconfig eth0.5 172.16.5.1 netmask 255.255.255.0 up
# vconfig add eth0 6
# ifconfig eth0.5 172.16.6.1 netmask 255.255.255.0 up

host A :
Code:
# ifconfig eth0 172.16.5.2 netmask 255.255.255.0 up

host B :
Code:
# ifconfig eth0 172.16.6.2 netmask 255.255.255.0 up

Arrange vlan configuration in switch :
Code:
VLAN_ID    VLAN_NAME     VLAN_MEMBER
1        Default VLAN   Untag:1; Tag:-; Not_member:2-16
5        vlan5              Untag:5; Tag:1; Not_member:2-4,6-16
6        vlan6              Untag:6; Tag:1; Not_member:2-5,7-16

ping result to both host A and host B from router gave same result : Destination Host Unreachable
ping command :
Code:
# ping 172.16.5.2 -I vlan5
# ping 172.16.6.2 -I vlan6

Please help, there's maybe I have wrong concept about vlan configuration?
Thank you very much.


Regards,
Denny
 

10 More Discussions You Might Find Interesting

1. Solaris

VLAN on SF280

hi, i tried to configure an VLAN interface on my SF280 based on the documentation on docs.sun.com # ifconfig eri1000 plumb up Oct 21 13:41:26 cmsmaster ip: ip_rput_dlpi(eri1000): DL_ERROR_ACK for DL_ATTACH_REQ(11), errno 8, unix 0 ifconfig: SIOCSLIFNAME for ip: eri1000: no such interface... (2 Replies)
Discussion started by: pressy
2 Replies

2. IP Networking

Network Access on Different Segment

I do have 2 different segment network which different platform on each segment. E.g. 20 segment, Windows OS can talk to Unix OS and 21 segment practice same rule. Further more, Windows OS from 20 segment can talk to 21 segment other OS but only the UNIX OS in 20 segment fail to talk to 21 segment.... (3 Replies)
Discussion started by: HASM
3 Replies

3. IP Networking

what is wrong with VLAN???

Hi all, so server: FreeBSD 7.0 release, interfaces on it DLINK DGE-528T with support of vlans :)) so first interface looks to LAN second to ISP. I created vlan1 with id 1 and gave to it ip address and plug it in tagged port of swith for vlan 1. so client from vlan1 reaches the server. it... (2 Replies)
Discussion started by: samar
2 Replies

4. AIX

how to know the vlan id?

I have a aix 5.3, two network adapter, configure as a etherchannel, how can I know the vlan id by command? (4 Replies)
Discussion started by: rainbow_bean
4 Replies

5. Programming

Data segment or Text segment

Hi, Whether the following piece of code is placed in the read-only memory of code (text) segment or data segment? char *a = "Hello"; I am getting two different answers while searching in google :( that's why the confusion is (7 Replies)
Discussion started by: royalibrahim
7 Replies

6. IP Networking

Implement inter vlan routing with Linux

Hello. I want to Communicate 2 VLAN with router like this solution: http://8pic.ir/images/83m0ouih8mmm9s1sfl56.jpg For this purpose I'm configuring 2 Linux system as a switch and connect 4 host to them. Then a router is added to scenario. The configuration of the switches is: On DUT1(Linux):... (1 Reply)
Discussion started by: zsn
1 Replies

7. Solaris

Solaris 9 VLAN tagging with ce interface

Hi, Is it possible to VLAN tag with a ce interface on Solaris 9? Link speed is gb. ce:0:ce0:link_speed 1000 I have a ce0 interface I would need to have access to another VLAN as well as the one it's currently on. What commands would I need to run? Thanks.;) (2 Replies)
Discussion started by: sparcman
2 Replies

8. Red Hat

Network issue in same vlan

We have two hosts in same vlan with same route rules. One of them is not able to connect to an outside IP while in another I get "failed: Connection timed out" while testing the connectivity through netcat. I have tried mtr /traceroute and it gives me the same results. Is there a netcat... (1 Reply)
Discussion started by: jacki
1 Replies

9. Solaris

Solaris non-global zone network vlan

Have 2 nics on physical system net0 phys 1500 up -- net1 phys 1500 up -- 1. I want to create a link aggregation with LACP enabled with above 2 nics 2. Create port-group(Like we create on ESXi) with VLAN-ID 2141 3. And assign this... (0 Replies)
Discussion started by: Shirishlnx
0 Replies

10. Solaris

IPMP over VLAN questions.

Hi Folks, I am currently moving systems to a new environment, with some changes to the network requirements on the systems. One of these changes is moving from just standard IPMP to using IPMP on top of a VLAN, I have used VLAN tagging befor without issue - however not with IPMP. What I... (2 Replies)
Discussion started by: gull04
2 Replies
VLAN(4) 						   BSD Kernel Interfaces Manual 						   VLAN(4)

NAME
vlan -- IEEE 802.1Q VLAN network interface SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device vlan Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_vlan_load="YES" DESCRIPTION
The vlan driver demultiplexes frames tagged according to the IEEE 802.1Q standard into logical vlan network interfaces, which allows rout- ing/bridging between multiple VLANs through a single switch trunk port. Each vlan interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf(5). To function, a vlan interface must be assigned a parent interface and numeric VLAN tag using ifconfig(8). A single parent can be assigned to multiple vlan interfaces provided they have different tags. The parent interface is likely to be an Ethernet card connected to a properly configured switch port. The VLAN tag should match one of those set up in the switched network. Initially vlan assumes the same minimum length for tagged and untagged frames. This mode is selected by the sysctl(8) variable net.link.vlan.soft_pad set to 0 (default). However, there are network devices that fail to adjust frame length, should it fall below the allowed minimum due to untagging. Such devices should be able to interoperate with vlan after changing the value of net.link.vlan.soft_pad to 1. In the latter mode, vlan will pad short frames before tagging them so that their length stays not less than the minimum value after untagging by the non-compliant devices. HARDWARE
The vlan driver supports efficient operation over parent interfaces that can provide help in processing VLANs. Such interfaces are automati- cally recognized by their capabilities. Depending on the level of sophistication found in a physical interface, it may do full VLAN process- ing or just be able to receive and transmit long frames (up to 1522 bytes including an Ethernet header and FCS). The capabilities may be user-controlled by the respective parameters to ifconfig(8), vlanhwtag and vlanmtu. However, a physical interface is not obliged to react to them: It may have either capability enabled permanently without a way to turn it off. The whole issue is very specific to a particular device and its driver. By now, the list of physical interfaces able of full VLAN processing in the hardware is limited to the following devices: ae(4), age(4), alc(4), ale(4), bce(4), bge(4), cxgb(4), em(4), ixgb(4), jme(4), msk(4), nge(4), re(4), sge(4), stge(4), ti(4), txp(4), and vge(4). The rest of the Ethernet interfaces can run VLANs using software emulation in the vlan driver. However, some of them lack the capability of transmitting and receiving long frames. Assigning such an interface as the parent to vlan will result in a reduced MTU on the corresponding vlan interfaces. In the modern Internet, this is likely to cause tcp(4) connectivity problems due to massive, inadequate icmp(4) filtering that breaks the Path MTU Discovery mechanism. The following interfaces support long frames for vlan natively: bfe(4), cas(4), dc(4), fwe(4), fxp(4), gem(4), hme(4), le(4), nfe(4), nve(4), rl(4), sf(4), sis(4), sk(4), ste(4), tl(4), tx(4), vr(4), and xl(4). The vlan driver automatically recognizes devices that natively support long frames for vlan use and calculates the appropriate frame MTU based on the capabilities of the parent interface. Some other interfaces not listed above may handle long frames, but they do not advertise this ability of theirs. The MTU setting on vlan can be corrected manually if used in conjunction with such a parent interface. SEE ALSO
ifconfig(8), sysctl(8) BUGS
No 802.1Q features except VLAN tagging are implemented. BSD
April 14, 2010 BSD
All times are GMT -4. The time now is 10:27 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy