Sponsored Content
Operating Systems Solaris istall sas raid HBA internal card Post 302249574 by photon on Tuesday 21st of October 2008 03:45:34 PM
Old 10-21-2008
istall sas raid HBA internal card

I need to install a raid HBA internal card on a T5240. The reason is I have
more drives and the current mother board controller does not support more
than 4 drives.

My question is I have raidctl set up on current drives. If I install new HBA
card do I have to delete current raidctl and make a new raidctl for new
HBA or will new HBA work with current raidctl?
 

10 More Discussions You Might Find Interesting

1. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies

2. SCO

driver needed for hp smartarry p200i sas raid controller

recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies

3. Solaris

Install Solaris 10 with an internal StorageTek SAS HBA Raid card

Hi all i would like to ask some suggests about my next job! I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid. The problem come in if every disk is now controlled by the HBA, how can I install the OS? No disk is being detected by the OS. SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies

4. UNIX for Advanced & Expert Users

Sun internal disks and HBA card

I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage. Would I sacrifice performance if I use the same HBA? Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies

5. AIX

Need HBA card driver

Hi All, SUN emulex HBA card has been installed on P520 box. When i run the cfgmgr i am getting the following message. lpar2#cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies

6. Solaris

installing solaris with StorageTek SAS RAID Internal HBA

i was given a task which needs to perform a raid 1 on the boot disk, and 4 other disks on raid 10. Is there any other alternative in installing solaris 10 other than through network installation?will be using solaris update 6. while reading through the user guide i got pretty confuse. ... (1 Reply)
Discussion started by: monstar1407
1 Replies

7. Solaris

T5240 and Internal SAS RAID Configuration help

Dear Friends, I need to configure T5240 with Internal SAS RAID HBA(SG-XPCIESAS-R-INT-Z).. T5240 uses 8 hard disks... From the documents of RAID card I have found that I need to create a jump start server to include three packages SUNWaac, StorMan, SUNWgccruntime if Im using solaris10 5/08... ... (5 Replies)
Discussion started by: nicktrix
5 Replies

8. Solaris

How to enable hba port of a two port hba card

Hi, i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port. ---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ---------- please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies

9. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies

10. Red Hat

HBA card faulty

Hi, How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
HBA_GetBindingCapability(3HBAAPI)	      Common Fibre Channel HBA Information Library Functions		 HBA_GetBindingCapability(3HBAAPI)

NAME
HBA_GetBindingCapability, HBA_GetBindingSupport, HBA_SetBindingSupport - return and sets binding capabilities on an HBA port SYNOPSIS
cc [ flag... ] file... -lHBAAPI [ library... ] #include <hbaapi.h> HBA_HANDLE HBA_GetBindingCapability(HBA_HANDLE handle, HBA_WWN hbaPortWWN, HBA_BIND_CAPABILITY *pFlags); HBA_STATUS HBA_GetBindingSupport(HBA_HANDLE handle, HBA_WWN hbaPortWWN, HBA_BIND_CAPABILITY *pFlags); void HBA_SetBindingSupport(HBA_HANDLE handle, HBA_WWN hbaPortWWN, HBA_BIND_CAPABILITY Flags); PARAMETERS
handle an open handle returned from HBA_OpenAdapter(3HBAAPI) hbaPortWWN the Port WWN of the local HBA through which the binding capabilities implemented by the HBA is returned pFlags a pointer to an HBA_BIND_CAPABILITY structure that returns the persistent binding capabilites implemented by the HBA Flags an HBA_BIND_CAPABILITY structure containing the persistent binding capabilites to enable for the HBA DESCRIPTION
The HBA_GetBindingCapability() function returns the binding capabilities implemented by the HBA. The HBA_GetBindingSupport() function returns the currently enabled binding capabilities for the HBA. The HBA_SetBindingSupport() function sets the currently enabled binding capabilites for the HBA to a subset of the binding capabilities implemented by the HBA. RETURN VALUES
The HBA_GetBindingCapability() and HBA_GetBindingSupport() functions return the following values: HBA_STATUS_OK Persistent binding capabilites have been returned. HBA_STATUS_ERROR_ILLEGAL_WWN Port WWN hbaPortWWN is not a WWN contained by the HBA referenced by handle. HBA_STATUS_ERROR_NOT_SUPPORTED The HBA handle specified by handle does not support persistent binding. HBA_STATUS_ERROR An error occurred. The value of pFlags remains unchanged and points to the persistent binding capabilites. The HBA_SetBindingSupport() function returns: HBA_STATUS_OK Persistent binding capabilites have been enabled. HBA_STATUS_ERROR_ILLEGAL_WWN Port WWN hbaPortWWN is not a WWN contained by the HBA referenced by handle. HBA_STATUS_ERROR_NOT_SUPPORTED The HBA handle specified by handle does not support persistent binding. HBA_STATUS_ERROR_INCAPABLE The flags argument contains a capability not implemented by the HBA. HBA_STATUS_ERROR An error occurred. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Interface Stability |Standard: FC-MI 1.92 (API | | |version 1) | +-----------------------------+-----------------------------+ | |Standard: FC-HBA Version 4 | | |(API version 2) | +-----------------------------+-----------------------------+ |MT-Level |Safe | +-----------------------------+-----------------------------+ SEE ALSO
libhbaapi(3LIB), attributes(5) T11 FC-MI Specification SunOS 5.10 1 Sep 2003 HBA_GetBindingCapability(3HBAAPI)
All times are GMT -4. The time now is 12:50 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy